4.
The
ServerGuide
program
prompts
you
to
insert
your
operating-system
CD
and
restart
the
server.
At
this
point,
the
installation
program
for
the
operating
system
takes
control
to
complete
the
installation.
Installing
your
operating
system
without
ServerGuide
If
you
have
already
configured
the
server
hardware
and
you
decide
not
to
use
the
ServerGuide
program
to
install
your
operating
system,
complete
the
following
steps
to
download
the
latest
operating-system
installation
instructions
from
the
IBM
Support
Web
page:
1.
Go
to
http://www.ibm.com/support/.
2.
In
the
Download
section,
click
Downloads
&
drivers
.
3.
On
the
“Downloads
and
drivers”
page,
in
the
Brand
field,
select
Servers
.
4.
In
the
Family
field,
select
System
x3800
.
5.
Click
Continue
.
6.
In
the
View
by
document
type
field,
select
OS
installation
.
7.
Select
the
instructions
for
your
operating
system.
Using
the
Boot
Menu
program
The
Boot
Menu
program
is
a
built-in
configuration
program
that
you
can
use
to
temporarily
redefine
the
first
startup
device
without
changing
settings
in
the
Configuration/Setup
Utility
program.
To
use
the
Boot
Menu
program,
complete
the
following
steps:
1.
Turn
off
the
server.
2.
Restart
the
server.
3.
Press
F12.
4.
Select
the
startup
device.
The
next
time
the
server
is
started,
it
returns
to
the
startup
sequence
that
is
set
in
the
Configuration/Setup
Utility
program.
Configuring
the
Gigabit
Ethernet
controller
The
Ethernet
controller
is
integrated
on
the
I/O
board.
It
provides
an
interface
for
connecting
to
a
10-Mbps,
100-Mbps,
or
1-Gbps
network
and
provides
full-duplex
(FDX)
capability,
which
enables
simultaneous
transmission
and
reception
of
data
on
the
network.
If
the
Ethernet
ports
in
the
server
support
auto-negotiation,
the
controller
detects
the
data-transfer
rate
(10BASE-T,
100BASE-TX,
or
1000BASE-T)
and
duplex
mode
(full-duplex
or
half-duplex)
of
the
network
and
automatically
operates
at
that
rate
and
mode.
You
do
not
have
to
set
any
jumpers
or
configure
the
controller.
However,
you
must
install
a
device
driver
to
enable
the
operating
system
to
address
the
controller.
Install
the
device
drivers
from
the
Broadcom
NetXtreme
Gigabit
Ethernet
Software
CD
that
comes
with
the
server.
For
information
about
configuring
the
Ethernet
controller,
see
the
Broadcom
NetXtreme
Gigabit
Ethernet
Software
CD
.
For
updated
information
about
configuring
the
controller,
see
http://www.ibm.com/support/.
Chapter
3.
Configuring
the
server
63
Содержание x3800 - System - 8865
