3 of 7
Step 3
Press down gently, but firmly, to ensure the card
is properly seated in the slot.
The bottom edge of the controller must be flush
with the slot.
Figure 3 Installing the ServeRAID SAS/SATA
Controller
Step 4
Secure the controller to the computer chassis
with the bracket screw.
Step 5
Reinstall the computer cover and reattach the
power cords.
Step 6
Turn on the power to the computer.
C O N N E C T I N G T H E S e r v e R A I D M 5 0 0 0
S E R I E S B A T T E R Y K I T R E M O T E LY
This section describes the two methods you can use to
connect the controller to a remote ServeRAID M5000 Series
Battery Kit using a cable or, where applicable, a cable and a
remote interposer board that are sold separately in a Remote
Battery Kit:
– Use the cable to connect the remote battery kit to the
BBU connector on the controller (
REMOTE M5000 SERIES BATTERY KIT TO THE
BBU CONNECTOR ON A ServeRAID SAS/SATA
CONTROLLER
– Use the cable to connect the remote battery kit to a
daughtercard that is connected to the BBU connector
on the controller (
M5000 SERIES BATTERY KIT TO AN INTERPOSER
CARD ON A ServeRAID SAS/SATA CONTROLLER
)
C O N N E C T I N G T H E R E M O T E M 5 0 0 0
S E R I E S B A T T E R Y K I T T O T H E B B U
C O N N E C T O R O N A S e r v e R A I D S A S /
S A T A C O N T R O L L E R
This section describes how to connect the remote M5000
Series Battery Kit to the BBU connector on the ServeRAID
M5025 SAS/SATA controller. You can connect the battery kit
in the same way to the other SAS/SATA controllers that use
this battery kit.
To connect the remote battery kit to the BBU connector on
the controller, perform the following tasks in order:
1.
Removing the Controller from the Computer
2.
Connecting the Cable Between the Controller and the
Remote M5000 Series Battery Kit
3.
Reinstalling the Controller on the Motherboard
Removing the Controller from the Computer
Follow these steps to remove the controller from the
computer.
Step 1
Turn off the power, and unplug the power cords.
Step 2
Ground yourself and make sure the system is
grounded.
Step 3
Remove the cover from the computer according
to the instructions in the system user’s manual to
allow access to the controller.
Step 4
Unplug all cables from the controller, remove the
screw attaching the bracket to the computer
chassis, and carefully remove the controller from
the slot.
Step 5
Place the controller on a flat, clean, static-free
surface, and continue with the next procedure.
Connecting the Cable Between the Controller and the
Remote M5000 Series Battery Kit
Follow these steps to connect the remote battery kit to the
BBU connector on the SAS/SATA controller.
Step 1
Ground yourself and make sure the system is
grounded.
Step 2
Remove the battery kit from the package.
Attention: Never
apply pressure to the battery kit when you
insert the controller. Instead, press down only on
the top edge of the controller, as shown in the
following figure.
Attention: Never
apply pressure to the battery kit when you
insert the controller. Instead, press down only on
the top edge of the controller, as shown in
Edge of Motherboard
LSIiBBU08 (Top View)
Bracket Screw
Edge of
Motherboard
85065-02
Press Here
Press Here
Model: BA
T 1S1P
Model: BA
T 1S1P
WA
RN
IN
G:
The battery used in
this device may present a risk of fire or
chemical burn if mistreated. DO NOT
dissemble, heat above 60C, crush or
puncture, short circuit external contacts,
or dispose in fire or water
.
WARNING:
The battery used in
this device may present a risk of fire or
chemical burn if mistreated. DO NOT
dissemble, heat above 60C, crush or
puncture, short circuit external contacts,
or dispose in fire or water
.
Contain
s:
So
ny US
454
261
A8
T C
ell
Rech
argeable Li-P
olym
er
Battery P
ack
Rating
:
3.7V
; 1.59A
h; 5.9W
h
Finishe
d in
C
hina
Contains:
Sony US454261A8T
Cell
Rechargeable Li-Polymer
Battery Pack
Rating:
3.7V; 1.59Ah; 5.9Wh
Finished in China
BB
U P
/N
: L
4-2
534
3-0
4
BBU P/N: L4-25343-04
BB
U S
/N
:S
Y02
700
225
SO
BBU S/N:SY02700225SO
Li-io
n
Li-ion
5
