IBM Storwize V5100 MTM 2078-12F Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 144

background image

CAUTION: CAUTION regarding IBM provided VENDOR LIFT TOOL:
• Operation of LIFT TOOL by authorized personnel only
• LIFT TOOL intended for use to assist, lift, install, remove units (load) up into rack elevations. It

is not to be used loaded transporting over major ramps nor as a replacement for such

designated tools like pallet jacks, walkies, fork trucks and such related relocation practices.

When this is not practicable, specially trained persons or services must be used (for instance,

riggers or movers). Read and completely understand the contents of LIFT TOOL operator's

manual before using.

• Read and completely understand the contents of LIFT TOOL operator's manual before using.

Failure to read, understand, obey safety rules, and follow instructions may result in property

damage and/or personal injury. If there are questions, contact the vendor's service and

support. Local paper manual must remain with machine in provided storage sleeve area.

Latest revision manual available on vendor's website.

• Test verify stabilizer brake function before each use. Do not over-force moving or rolling the

LIFT TOOL with stabilizer brake engaged.

• Do not raise, lower or slide platform load shelf unless stabilizer (brake pedal jack) is fully

engaged. Keep stabilizer brake engaged when not in use or motion.

• Do not move LIFT TOOL while platform is raised, except for minor positioning.
• Do not exceed rated load capacity. See LOAD CAPACITY CHART regarding maximum loads at

center versus edge of extended platform.

• Only raise load if properly centered on platform. Do not place more than 200 lb (91 kg) on

edge of sliding platform shelf also considering the load's center of mass/gravity (CoG).

• Do not corner load the platform tilt riser accessory option. Secure platform riser tilt option to

main shelf in all four (4x) locations with provided hardware only, prior to use. Load objects are

designed to slide on/off smooth platforms without appreciable force, so take care not to push

or lean. Keep riser tilt option flat at all times except for final minor adjustment when needed.

• Do not stand under overhanging load.
• Do not use on uneven surface, incline or decline (major ramps).
• Do not stack loads. (C048, part 1 of 2)

Safety and environmental notices xv

«
...
13
14
15
16
17
...
»

Содержание Storwize V5100 MTM 2078-12F

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Storwize V5100 MTM 2078-12F

Бренд: Samsung Страницы: 2

Бренд: proavio Страницы: 6

Бренд: Blaupunkt Страницы: 8

Бренд: Sharp Страницы: 33

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 14

Бренд: Philips Страницы: 18

Бренд: Philips Страницы: 15

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 20

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 32

Бренд: Philips Страницы: 30

Бренд: Philips Страницы: 35

Бренд: RCA Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды