background image

necessary replacement parts. With access to the storage system, IBM service personnel can complete
service tasks, such as viewing error logs or initiating trace and dump retrievals.

Call home notifications are sent through email from a simple mail transport protocol (SMTP) server. The
storage system's Mail Service function is used by the system to send outgoing call-home emails to IBM.

Note:

You must configure the SMTP email system by using the mail service function to enable the system

to send outgoing emails for the call home function. (See “Configuring the mail service.” The email
configuration rules must not inhibit call home emails from being sent in real time. Emails with

Importance

or

X-Priority

in the email header must not be delayed. For example, system emails must not

be placed in a queue for later delivery or filtered for priority.

Table 1. Call home configuration information

Call home configuration
requirement

Value

Details

SMTP port

25

Your SMTP server must be reachable
on port 25 from the management IP
address.

SMTP address

IP address

The SMTP IP address.

Email destination address

[email protected]

The SMTP server must allow relaying
to this email address.

Email source address

[email protected] or
customer-defined

The default email address from
which the email is sent. You can set
this email address to conform to your
email relay rules.

Configuring the mail service

The mail service function provides system event email notifications and the ability to email the system
report directly for support purposes.

About this task

To configure the mail service settings, complete the following steps:

Procedure

1.

In the web interface, select the

Services

node in the tree and clicking the

Mail

node, which displays

an overview pane.

2.

Clicking the

Configure

button opens the configuration wizard. Use this wizard to enable available

functions, to set the simple mail transport protocol (SMTP) server, and to enter target email addresses.
Any available mail service functions can be enabled by checking the box that corresponds to the
function. The SMTP server might be set manually or found automatically from DHCP by setting the
server value to

Default

.

3.

Specify up to five email targets to receive emails that are sent by the service. The

[email protected]

email address is stored internally and does not need to be added manually.

4.

You can customize the email source address by using the command-line interface:

a.

From a Telnet or Secure Shell (SSH) client, access the system by using the system IP address.

b.

Log in by using the default user name

username

and the default password

password

, or your

system's unique user name and password.

c.

Enter

system call_home_config

<SMTP IP address><custom email address>

at the command

prompt.

<SMTP IP address>

can be the IP address of the default mail System SMTP server, or the

IP address of a different SMTP of your choice.

12

IBM FlashSystem: Installing the IBM FlashSystem 810

Содержание FlashSystem 810







































Отзывы: