IBM eServer xSeries 235 Type 8671 Скачать руководство пользователя страница 66

Страница: 66 / 102

c. Disconnect the other device power connectors (P4 and P6) from the rear of

any other devices in the server.

d. Disconnect the SCSI cable (P2) from the SCSI backplane.

e. Disconnect the power cable (P1) from the J4 connector on the system

board.

f. Disconnect the power signal cable (P3) from the J10 connector on the

system board.

g. If your server has the 3-Pack Ultra320 Hot-Swap Expansion option

installed, disconnect the power connector (P8) from the power connector
on the 3-Pack backplane.

5. Remove the fixed power supply (see the following illustration).

a. From the rear of the server, remove the two screws at each side of the

fixed power supply.

b. Gently pull the power supply from the server, making sure the cables do

not snag on the chassis or system board.

Note:

You might need to insert a fingernail or screwdriver blade behind
one corner of the power supply to begin moving it.

Attention:

When installing the power supply, do not pull it into position by its

cables.

IBM xSeries 235 Type 8671: Option Installation Guide

Содержание eServer xSeries 235 Type 8671







































































































Результаты поиска

Содержание eServer xSeries 235 Type 8671

Отзывы:

IBM eServer xSeries 235 Type 8671, Руководство по установке опций, Страница: 66 / 102

Результаты поиска

Содержание eServer xSeries 235 Type 8671

Отзывы: