manualshive.com logo in svg

IBM Deskstar Deskstar 3, Инструкция по установке и справочник, Страница: 26 / 72

Поделиться
Скачать
IBM Deskstar Deskstar 3 Скачать руководство пользователя страница 26

    

19

•

To use the provided ATA/IDE cable, remove the existing cable from the primary
ATA/IDE connector of your motherboard or controller card.

•

Attach the blue connector of the ATA/IDE cable to the ATA/IDE connector marked
“Primary” or “0” on the motherboard or controller card.  The primary ATA/IDE
connector controls the first and second ATA/IDE devices in the system.

Note: The pin 1 edge of an ATA/IDE cable is marked with a colored stripe. The connectors are also
keyed to insert one way only.

•

Attach a power cable to each hard disk drive.

•

Attach the black connector of the ATA/IDE cable to the Master drive.

•

Attach the gray connector of the ATA/IDE cable to the Slave drive.

Mount the drive

Note: Drive bays and other enclosures vary in size and orientation from system to system.  They

m ay be oriented vertically, horizontally, upside dow n, or sidew ays.

 The IBM Deskstar can be

mounted with any side or end vertical or horizontal, but must not be mounted in a tilted position.

•

Mount the drive as instructed by your computer system manual.

Содержание Deskstar Deskstar 3









































































Отзывы:

Нет отзывов