Rack Installations
xSeries 440 4 U, rack-optimized servers are designed to
be installed in a 19-inch rack cabinet designed for 26-inch
deep devices, such as the NetBAY42 ER, NetBAY42 SR,
or NetBAY25 SR.
Towerlike or mini-rack xSeries 440
installations can be created with the NetBAY11 Standard
Rack Cabinet.
If you use a non-IBM rack, the cabinet must meet the
EIA-310-D standards with a depth of at least 28 inches.
Also, adequate space (approximately two inches for the
front bezel and one inch for air flow) must be maintained
from the slide assembly to the front door of the rack
cabinet to allow sufficient space for the door to close and
provide adequate air flow.
Power Considerations
The xSeries 440 includes two, standard 1050-watt,
hot-swap, redundant power supplies.
This provides
sufficient power to support n+n redundancy for all
configurations.
Cable Orders:
The 10/100/1000 Mbps full-duplex, Ethernet
PCI controller, standard with xSeries 440, is connected
directly to a RJ-45 connector.
The RJ-45 connector
provides a 10BaseT or 100/1000Base-TX interface for
connecting twisted-pair cable to the Ethernet network.
Cabling is not included with the server.
To connect the
Ethernet controller to a repeater or switch, use an
unshielded twisted pair (UTP) cable with RJ-45 connectors
at both ends. For 100/1000 Mbps operation, Category 5
cabling must be used.
For 10 Mbps operation,
Category 3, or better, cabling must be used.
There are no additional cabling requirements, other than
for system power, keyboard, mouse, and monitor
connections.
Installability:
The xSeries 440 requires about 20 minutes
for installation.
Installation includes unpacking, setting
up, and powering on the system.
Additional time is
required to install an operating system, additional
adapters, or features.
Packaging:
One box
System Unit Carton
•
System Unit
•
Rack components:
−
Slides and cable management arm
−
Two 9-foot 220 V intra-rack cables
Country Kit Carton
•
Two line cords (220 V for wall outlet)
•
xSeries 440 Installation Guide
•
Safety booklet
•
SCSI cable
•
Rack Install Template
•
ServerGuide and IBM Director
•
CD-ROM Packages
•
On/off switch cover
The xSeries 440 system is shipped as a single package.
The country kit carton is contained inside the top portion
of the system unit carton.
xSeries SMP Expansion Module with Dual Xeon
Processors
2.4 GHz/512 KB
•
Card assembly including two 2.4 GHz Xeon processors
and voltage regulator module (VRM)
•
Card cover assembly
•
Two 10-inch scalability cables
•
Installation instructions/warranty
Security, Auditability, and Control
Security and auditability features include:
•
Power-on and privileged access password functions
provide controls of who has access to the data and
server setup program on the server.
•
Set unattended boot mode allows the system keyboard
to be locked to all entries except the password and at
the same time allows other computers on the network
to access the system disk drive.
•
Selectable boot sequence can be used to prevent
unauthorized installation of software or removal of
data from the diskette drive.
Limitations:
The xSeries 440 has no security intrusion
detection; therefore, it should be installed in a rack
environment that provides security through lockable
doors or other security measures.
It is a customer
′
s
responsibility to ensure that the server is secure to
protect sensitive data.
The customer is responsible for evaluation, selection, and
implementation of security features, administrative
procedures, and appropriate controls in application
systems and communications facilities.
Terms and Conditions
This product is available for purchase under the terms of
the IBM Customer Agreement (ICA).
IBM hardware products are manufactured from new parts.
In some cases, the hardware product may have been
previously installed.
Regardless, IBM warranty terms apply.
IBM Credit Corporation Financing:
Yes
To obtain copies of the IBM Statement of Limited
Warranty, contact your IBM representative or IBM
Business Partner, or visit:
http://www.ibm.com/servers/support/
machine_warranties/
Warranty Period
•
System hardware: One year on parts and labor
•
Optional features: One year
Warranty Service
System hardware: IBM On-site Repair (IOR), 24 hours a
day, 7 days a week, same day response
Optional features:
Optional features are designated as
Customer Carry-in Exchange/Repair (CCE/CCR).
Optional IBM features initially installed with an xSeries
server carry the same warranty as the system.
If
installed after the initial system installation, they carry
the balance of the system warranty or the optional feature
warranty, whichever is greater.
102-205
-4-
