IBM 7208 Скачать руководство пользователя страница 28

Страница: 28 / 92

1.1.3 Liquid Crystal Display

The 7208 Tape Drive features a liquid crystal display (LCD) ( 5 in Figure 4 in topic 1.1). The LCD provides operating and error messages.

Figure 6 shows a list of messages that display on the LCD.

+------------------------------------------------------------------------+

¦ Figure 6. LCD Messages ¦

+------------------------------------------------------------------------¦

¦ Reset Messages ¦

+------------------------------------------------------------------------¦

¦ RESET ¦ The first message to appear during the ¦

¦ ¦ power-on sequence. ¦

+-----------------------+------------------------------------------------¦

¦ MODEL: ¦ Variable information about the tape drive, in ¦

¦ ¦ this case IBM-20GB. ¦

+-----------------------+------------------------------------------------¦

¦ SUBMOD: ¦ The submodel number of the tape drive. ¦

+-----------------------+------------------------------------------------¦

¦ SN: ¦ The serial number of the tape drive. ¦

+-----------------------+------------------------------------------------¦

¦ CODE: ¦ The level of the tape drive's firmware. ¦

+-----------------------+------------------------------------------------¦

¦ LAST CLN: ¦ The number of hours since the last cleaning. ¦

+-----------------------+------------------------------------------------¦

¦ COMPRESSION: ¦ Whether data compression is turned on (the ¦

¦ ¦ default) or turned off. ¦

+-----------------------+------------------------------------------------¦

¦ SINGLE ENDED or ¦ The type of SCSI input/output electrical ¦

¦ DIFFERENTIAL ¦ interface. ¦

+-----------------------+------------------------------------------------¦

¦ WIDE ¦ The width of the SCSI bus (measured in bits or ¦

¦ ¦ bytes). ¦

+-----------------------+------------------------------------------------¦

¦ SCSI ID: ¦ The SCSI address of the tape drive (0 through ¦

¦ ¦ 15). The default is 0. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The current language used on the LCD. To ¦

¦ ¦ change the language, turn off the power to the ¦

¦ LANGUAGE: ¦ tape drive. Press and hold the unload button ¦

¦ ¦ immediately after turning the power back on. ¦

¦ ¦ When the desired language displays, release ¦

¦ ¦ the unload button. ¦

+------------------------------------------------------------------------¦

¦ Tape Drive Status Messages ¦

+------------------------------------------------------------------------¦

¦ READY-NOTAPE ¦ The tape drive is ready to accept a cartridge. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ LOADING.... ¦ The tape drive is loading the tape. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ READY-TAPE ¦ The tape drive successfully loaded the tape ¦

¦ ¦ and is ready for read or write operations. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ ILLEGAL TAPE ¦ An unsuitable tape has been loaded and ¦

¦ ¦ rejected. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The unload button was pressed. The tape drive ¦

¦ << EJECT====== ¦ will eject the cartridge as soon as it ¦

¦ ¦ finishes the current operation. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The unload button was pressed, and the system ¦

¦ ¦ EJECT PREVNT ¦ software has issued a command to prevent the ¦

¦ ¦ eject function. ¦

+------------------------------------------------------------------------¦

¦ Tape Motion Messages ¦

+------------------------------------------------------------------------¦

¦ ¦ The tape drive is reading data. The + sign ¦

¦ ¦ appears when the data is compressed. The boxes ¦

READ+¦¦¦¦¦= ¦ (¦) represent the amount of tape processed ¦

¦ ¦ (out of a total of six boxes). The = sign ¦

¦ ¦ represents the amount of unprocessed tape. ¦

+-----------------------+------------------------------------------------¦

WRITE+¦¦¦¦= ¦ The tape drive is writing data. The + sign ¦

¦ ¦ appears when the data is compressed. ¦

+-----------------------+------------------------------------------------¦

¦ / PROTECTED ¦ The tape drive cannot write data because the ¦

¦ ¦ data cartridge is write-protected. ¦

+-----------------------+------------------------------------------------¦

¦ ¦ The tape drive cannot write to the type of ¦

¦ / ILLEGAL WRT ¦ data cartridge inserted. This message remains ¦

¦ ¦ until a proper tape is inserted or a tape ¦

¦ ¦ motion command is issued. ¦

+-----------------------+------------------------------------------------¦

7208 Tape Drive Service Guide

Liquid Crystal Display

¦ Copyright IBM Corp. 1998

1.1.3 - 1

All manuals and user guides at all-guides.com

Содержание 7208





























































































Результаты поиска

Содержание 7208

Отзывы:

IBM 7208, Руководство по обслуживанию, Страница: 28 / 92

Результаты поиска

Содержание 7208

Отзывы: