IAME Parilla Leopard TaG Series страница 8 Скачать руководство пользователя

Страница: 8 / 46

MAN048 ING

3.2

INSTALL THE WATER COOLING SYSTEM

NOTE:
To install the water pump belts it is necessary to remove the rear axle.

REINSTALL THE REAR AXLE AFTER
HAVING INSERTED TWO BELTS

SUGGESTION:
INSTALL OTHER TWO BELTS AS SPARES
AND FIX THEM WITH TAPE TO THE AXLE.

INSTALL THE WATER PUMP (1 SCREW
M8x45 WITH WASHER AND NUT) ON THE
PUMP BRACKET ON THE REAR CROSS
RAIL (SEE FIG. 1).
TORQUE AT 18÷22 Nm (160÷190 inlb)

IN CASE THERE IS NO BRACKET FOR THIS
PURPOSE IT IS NECESSARY TO INSTALL
THE PUMP ON REMOVABLE CLAMPS
AVAILABLE IN DIFFERENT DIAMETERS
(

28/30/32mm).

ASSEMBLE THE PUMP FIXING BRACKET ON
THE CLAMP (N°2 SCREWS M6x12) AND
PLACE THE CLAMPS ON THE REAR CROSS
RAIL (N°2 SCREWS M6x25).
INSTALL THE PUMP ON THE BRACKET (N°1
SCREW M8x45 WITH WASHER AND NUT –
SEE FIG. 2).

TIGHTEN BY HAND THE SCREW ON THE
PUMP LETTING IT FREE TO ROTATE

FOR

THE ALIGNMENT AND TENSIONING OF THE
BELTS.

INSTALL ON THE AXLE THE DRIVING
PULLEY (N° 2 CLAMPS AVAILABLE IN
DIFFERENT DIAMETERS

30/35/40/50mm)

ALIGNING ITS RACE WITH THE DRIVEN
PULLEY (SEE FIG.3).
FIX THE TWO CLAMPS WITH 2 SCREWS
M5x22 (TIGHTEN AT 6÷ 8 Nm) (50÷70 inlb).

TIGHTEN THE TWO SCREWS M6x25 ON
THE PUMP FIXING CLAMPS AND THE
SCREWS M6x12 ON THE PUMP FIXING
BRACKET.
TIGHTEN AT 8÷10 Nm (70÷90 inlb)

Fig.3

Fig.1

Fig.2

SCREW M6X12

PUMP FIX. BRACKET

SCREW M8X45

SCREW M6X25

SCREW M5X22

Содержание Parilla Leopard TaG Series















































Результаты поиска

Содержание Parilla Leopard TaG Series

Отзывы:

Похожие инструкции для Parilla Leopard TaG Series

Бренды по названию

Популярные бренды

IAME Parilla Leopard TaG Series, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание Parilla Leopard TaG Series

Отзывы:

Похожие инструкции для Parilla Leopard TaG Series

Бренды по названию

Популярные бренды