IAME Parilla Leopard TaG Series страница 25 Скачать руководство пользователя

Страница: 25 / 46

MAN048 ING

5 CARBURETOR ADJUSTMENT GUIDE

1 T.O.

RICH LEAN

T.O.

T.O. = TURNS OPEN

Normally the correct setting of the mixture screws is the following:

L (close the screw completely and then open): 1 ¼ ÷ 1 ½ T.O.

H (close the screw completely and then open): 1 ÷ 1 ¼ T.O.

Based on various factors as altitude, ambient temperature etc. it might be necessary to reset the carburetor to optimize
the performance of the engine.

ATTENTION:

Never lean too much as lean mixture will overheat engine and cause seizure

Do not force H or L closed. It may damage the precision machined orifice and render the carb unserviceable.

The adjustment of screw must be performed with warm engine.

(H)

Adjust T.O. from closed to
approximately

1 ¼ .T.O.

(L)

Adjust T.O. from closed to approximately

1 ¼ T.O

(I)

Close by further 1 ½ T.O.
after contact with throttle
lever.

Start the engine and warm it. If RPM too
high adjust

counterclockwise until clutch is

disengaged.

Turn c.c.w. until max. R.P.M.
is reached. Adjust further
fractionally for rich idle.
Trigger accelerator.

If R.P.M.
decreases

(L)

Slowly adjust clockwise

If R.P.M.
increases

Continue  to  turn  clockwise
until  max.  R.P.M.  is  reached.
Adjust  c.c.w.  fractionally  for
rich idle.
Trigger accelerator.

Engine is now idling at max. attainable
R.P.M. or slightly lower on rich side.

Adjust

counterclockwise until 2000 ÷ 2500

R.P.M. is reached.

Recheck

screw for optimum setting

required.

Adjust

until best possible free speed is

reached. Turn clockwise for higher R.P.M.
Counterclockwise for lower R.P.M.

Adjust

slightly richer by

1/8 ÷ ¼ T.O.

bad

acceleration

Return to idle and check acceleration for
quick response and smooth pickup.

good

acceleration

Engine is ready to operate.

( I )

THROTTLE

SPEED SCREW

( L )

LOW SPEED FUEL MIXTURE

( H )

HIGH SPEED FUEL MIXTURE

Содержание Parilla Leopard TaG Series















































Результаты поиска

Содержание Parilla Leopard TaG Series

Отзывы:

Похожие инструкции для Parilla Leopard TaG Series

Бренды по названию

Популярные бренды

IAME Parilla Leopard TaG Series, Инструкция по сборке и руководство пользователя

Результаты поиска

Содержание Parilla Leopard TaG Series

Отзывы:

Похожие инструкции для Parilla Leopard TaG Series

Бренды по названию

Популярные бренды