IAI IF Скачать руководство пользователя страница 9

Страница: 9 / 48

NTELLIGENT ACTUATOR

Table of Contents

1. Foreword
2. Safety Precautions

2.1 Basic Operating Instructions

2.2 Maintenance and Inspection

3. Warranty

3.1 Warranty Period

3.2 Scope of Warranty

4. Names of the Parts
5. Transporting • Handling

5.1 Handling of the Single Unit

5.1.1 Handling of the Packed Unit

5.1.2 Handling the Actuator After It is Unpacked

5.2 Handling of the Assembled Unit

5.2.1 Shipping of the Assembled Unit from Our Company

5.2.2 Handling of the Assembled Unit with Peripheral Equipment

6. Installation and Storage Enviroment

6.1 Installation Environment

6.2 Storage Environment

7. Installation

7.1 Installing the Main Body

7.2 Mounting Surface

7.3 Clamp Screws

7.4 Mounting and the T-Slot (Option)

7.5 Attaching the Slider Carrying the Pay load

................................................................................................................... 1

.................................................................................................... 1

...................................................................................... 1
...................................................................................... 1

.................................................................................................................... 2

...................................................................................................... 2

.................................................................................................. 2

................................................................................................... 3

............................................................................................. 4

....................................................................................... 4

.............................................................................. 4

............................................................ 4

................................................................................. 5

................................................ 5

...................................... 5

......................................................................... 6

........................................................................................... 6

.............................................................................................. 6

................................................................................................................. 7

........................................................................................... 7

.................................................................................................... 8

........................................................................................................ 9

............................................................................... 9

.................................................................. 10

Содержание IF

















































Результаты поиска

Содержание IF

Отзывы:

Бренды по названию

Популярные бренды

IAI IF, Руководство по эксплуатации

Результаты поиска

Содержание IF

Отзывы:

Бренды по названию

Популярные бренды