IAI IF Скачать руководство пользователя страница 12

I

NTELLIGENT ACTUATOR

3. Warranty

3.1  Warranty Period

3.2  Scope of Warranty

Warranty period shall be either of the following periods whichever ends first:

• 18 months after shipment from our factory
• 12 months after delivery to a specified location
• 2500 hours of operation time

If a breakdown occurs within the period specified above and is due to the manufacturer's error, we will repair the unit at no 
cost. However, the following items are not covered by this warranty.

• Faded paint or other changes that occur naturally over time.
• Consumable components that wear out with use (stainless sheet, etc.).
• Unit seems to be noisy or similar impressions that do not affect machinery performance.
• Damage resulting from improper handling by the user or lack of proper maintenance.
• Any alterations made by other than IAI or its representatives.
• Breakdowns caused by using controllers made by other manufacturers.
• Any damages caused by fire and other natural disasters or accidents.

The warranty pertains to the purchased product itself and does not cover any damages that might arise from a breakdown 
of the supplied product.
Any repairs will be done at our factory. Even if the product is still covered under the warranty period, we will assess a 
separate charge for sending technicians to the customer's site.

 2

Содержание IF

















































Отзывы: