IAG IAG-ENG-7252 Скачать руководство пользователя

Страница: 36 / 36

IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com

51. Before proceeding, please look over the check list

below:

Check Over List

Are all coolant fittings tight?

Are (2) coolant clamps correctly fitted on the turbo coolant

pipe and the expansion tank?

Was any coolant spilled in the engine bay cleaned up?

Are the hose clamps on the silicone couplers tight?

Are the following connections zip tied:

•

½” valve cover ports

•

Both connections on the Y-fitting that is attached

to the block

•

All 3 side ports on the AOS

•

The top breather port

52. After you have reviewed the check list, proceed to start

the vehicle and check for leaks. After the engine has heat

cycled, you can check the coolant level and replace any

coolant that was lost during installation.

Содержание IAG-ENG-7252





































Результаты поиска

Содержание IAG-ENG-7252

Отзывы:

Похожие инструкции для IAG-ENG-7252

Бренды по названию

Популярные бренды

IAG IAG-ENG-7252, Руководство по установке

Результаты поиска

Содержание IAG-ENG-7252

Отзывы:

Похожие инструкции для IAG-ENG-7252

Бренды по названию

Популярные бренды