background image

I S TECHNOLOGY SOLUTIONS

4

cables when in direct contact with water is not suggested. The internal charger is a “Smart Charger”, 

it will not over-charge the battery and can be left plugged in for long periods of time. To charge the 

Brake Pro™, simply follow the steps below.

NOTE: It is highly recommended that new devices be charges for several hours when first 

received.

1.  Insert the black GFCI plug into any 110V outlet (or appropriate outlet for international devices).
2.  To begin charging, push the RESET button located on the GFCI plug.
3. 

No light will appear if the unit is off. To check if the unit is charging, turn the unit on. A voltage 

reading of 14+V indicates the unit is charging. Once the reading drops to 13.0 - 13.2V, the unit 

has charged. Turn the unit off to charge the unit faster. 

4.  A fully charged battery without AC power (not plugged in) will show 12.6 - 12.8V.
5.  When fully charged, the Brake Pro™is capable of running for up to 8 hours. If, however, 

the battery runs down to an unacceptable voltage, the Brake Pro™ may experience 

difficulties communicating with the handheld tablet or operating the internal components. If 

communication problems are experienced, charging the Brake Pro™ is recommended.

NOTE: Brake Pro™ should be charged when volt meter falls below 12V, and should never be 

used with volt meter below 11V.

The Brake Pro™ unit comes with a handheld tablet for operating the device. The tablet runs on a 

rechargeable battery that needs to be maintained in order to operate properly. To charge the tablet, 

follow the steps below.

1.  Plug the black charger, included with the shipment, into any standard 110V outlet (or 

appropriate outlet for international devices).

2.  Plug the round end of the charger into the charging port. This is found underneath the tab on 

the edge of the tablet.

3.  The tablet will display a green light next to the battery icon on the right edge of the tablet if all 

connections are correct.

Содержание BRAKE PRO S-4027



































Отзывы: