background image

I S TECHNOLOGY SOLUTIONS

27

Software Operations

Version Number

The Brake Pro™ Application shows the version number at the bottom center of the screen. The 

version number follows the AAR specification.

To check to see if the latest version is installed, search for “brakepro” in the Google Play Store. Tap 

the Brake Pro by I S Technology Solutions icon. Tap About This App. Make sure the version number 

in the Play Store matches the version number in the application.

Installing the Brake Pro™ Application

Sometimes the Brake Pro™ Application may become corrupted and need to be uninstalled and 

reinstalled.

1.  To uninstall the application, click and hold the icon. A trash can icon will appear, drag the 

application to the trash can and release. A message will be displayed that the application has 

been uninstalled.

2.  Open the Google Play store app. Search for “brakepro”. The application will appear in the 

results. Tap it, and click Install.

3.  Once the application has been installed, you will need to perform the Reading the 

Configuration File steps below.

Updating the Brake Pro™ Application

Tablets are sent out with auto-updating turned on. When the tablet is connected to a WiFi network, it 

will check for updates, and download and install them, if available. To check for updates and manually 

install them, perform the below.

Item

Name

Manufacturer ID & 

Version Number

Revision

Number

AAR

Version Year

Содержание BRAKE PRO S-4027



































Отзывы: