background image

 

ISH & ISHV & ISHVS CONNECTOR Instruction Manual

 

Document No. 

HDM-0002 

 

 
 

 

22

  / 

29

 

Confidential C                                                                                                                                                                                                   

 
 
 
 
 
 
 
 
 

Notes 

Do not pry with the releasing jig or female terminals during operation. Check for any deformation or damage on the female terminals and the 
female housing after releasing the terminals. (see Fig.44) 

Do not continue applying force once the lance has reached the ceiling, or the ceiling will be deformed 

    or releasing jig may be damaged by excessive force. Take sufficient care when handling.(see Fig.45) 

If there is any damage or deformation on the terminal or the housing, do not use the damaged item. Replace the item with a new one. 

Only use the terminal releasing jig specified. 

Do not insert the releasing jig into the cavities (see Fig.46) 
If the releasing jig is inserted into the cavities by mistake, the terminal may be damaged. Replace the terminal with a new terminal. 

   

Care must be taken not to damage edge of the jig (e.g. from dropping, etc.) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

             

Fig43  Deformed  ceiling,  Damaged  releasing  jig 

 

Fig40. Correct orientation of the releasing jig and the housing lance 

 

Fig41. Terminal releasing jig in operation 

Fig 44 Incorrect insertion of the releasing jig 

Direction of release 

Terminal releasing jig 

Terminal releasing jig 

Pivot of   

releasing jig 

Cavity 

 

Damage caused by releasing jig. 

Deformed ceiling 

Damaged releasing jig 

Excessive rotation 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

   

 

 

Fig42  Damage  caused  by  releasing  jig 

 

Содержание ISH 26P






























Отзывы: