I-PEX ISH 26P Скачать руководство пользователя страница 25

Страница: 25 / 29

ISH & ISHV & ISHVS CONNECTOR Instruction Manual

Document No.

HDM-0002

Confidential C

10. Unmating of connector

①

Hold the female connector and push it in lightly.

②

While holding the female connector in, press down fully on the end of the arm (see Fig. 52).

③

Keep pressing the lock down, and pull out the female connector.

Notes

①

Do not pull out the female connector without the lock arm fully pressed down.
It may cause damage or deformation to the connector.

②

Hold and pull the female connector (not the wires), when disengaging the female connectors.

③

If there is any damage or deformation, do not use the damaged item.
Replace the item with a new one.

④

Pressing down the end of the lock arm may not release the lock fully (See Fig. 53)

Fig52. Lock arm

③

Pull out female connector

Direction of pressing

When the lock arm is pressed on the front part,
center of the lock is bent.

When the lock arm is pressed on the end,
back portion of the lock is bent.

Fig53. Mechanism of the lock

①

Push in lightly

②

Press down on the edge

Push point

Press vertically with a thumb

Good

No good

Содержание ISH 26P






























Результаты поиска

Содержание ISH 26P

Отзывы:

Похожие инструкции для ISH 26P

Бренды по названию

Популярные бренды

I-PEX ISH 26P, Инструкция по эксплуатации

Результаты поиска

Содержание ISH 26P

Отзывы:

Похожие инструкции для ISH 26P

Бренды по названию

Популярные бренды