background image

6-20

CHECK COOLANT

Check if the level of coolant in reservoir tank is
between FULL and LOW.
Add the mixture of antifreeze and water after
removing the cap of the reservoir tank if coolant
is not sufficient.
Be sure to add the coolant by opening the cap of
radiator when coolant level is below LOW.
Replace gasket of radiator cap when it is
damaged.
Hot coolant can spray out if radiator cap is
removed while engine is hot. Remove the
cap after the engine has cooled down.

FLUSHING AND REFILLING OF RADIATOR

Change coolant
Avoid prolonged and repeated skin contact
with used antifreeze. Such prolonged
repeated contact can cause skin disorders or
other bodily injury.
Avoid excessive contact-wash thoroughly
after contact.
Keep out of reach of children.
Protect the environment : Handling and
disposal of used antifreeze can be subject to
federal, state, and local law regulation.
Use authorized waste disposal facilities,
including civic amenity sites and garages
providing authorized facilities for the receipt
of used antifreeze.
If in doubt, contact your local authorities for
guidance as to proper handling of used
antifreeze.

HYUNDAI

FULL

LOW

NOT OK

OK

3)

(1)

(2)

(3)

(4)

11076MI06

21076MA08

21076MA09

4)

(1)

Содержание Robex 130 SMART





















































































































































Отзывы: