Hyster H177 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 80

background image

8000 SRM 707

Maintenance Procedures Every 250 Hours or 6 Weeks

1.

IDLE SPEED SCREW

2.

IDLE MIXTURE SCREW

3.

IDLE CONTROL SCREW

4.

IDLE CONTROL ACTUATOR

5.

VACUUM HOSE CONNECTION

Figure 25. LPG Carburetor

4.

Check the idle control adjustment as follows:

a. Adjust idle speed and mixture as described

above.

b. Put transmission in NEUTRAL and discon-

nect vacuum hose from idle control actuator.
Adjust engine idle speed to 1370 to 1430 rpm
with idle control screw.

c.

Install vacuum hose and clamp to idle control
actuator.

d. Check idle speed. If idle speed is higher than

specifications, make adjustment at idle con-
trol screw.

CAUTION

The adjustment of the throttle cable must be
correct, or it can break during operation. The
accelerator pedal or the MONOTROL pedal
must reach the pedal stop (floor plate) by the
time the throttle plate in the carburetor is
fully open.

5.

Check that engine runs at its governed speed
when accelerator pedal or MONOTROL pedal
reaches floor plate. If necessary, adjust throttle
cable at bracket on engine. Loosen lock nuts and
move cable as necessary. Check that maximum
engine speed is within specifications shown in
the Maintenance Schedule.

Engine Speed, LPG Carburetor, GM 3.0L
(Impco)

1.

The engine must be at the normal operating tem-
perature. Connect a tachometer to engine.

2.

Turn idle speed screw until idle speed is within
specifications shown in the Maintenance Sched-
ule. See Figure 26.

3.

Adjusting the idle mixture screw will change en-
gine speed. Adjust idle mixture screw to obtain
maximum engine rpm. Adjust idle speed again
as described in Step 2.

1.

IDLE SPEED SCREW

2.

IDLE MIXTURE SCREW

3.

VACUUM HOSE CONNECTION

4.

IDLE CONTROL ACTUATOR

5.

IDLE CONTROL SCREW

Figure 26. GM 3.0L Engine LPG Carburetor

39

«
...
43
44
45
46
47
...
»

Содержание H177

















































































Отзывы:

Нет отзывов

Похожие инструкции для H177

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: VAT Страницы: 29

Бренд: Balboa Instruments Страницы: 19

Бренд: Jetline Страницы: 58

Бренд: Garmin Страницы: 4

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Insignia Страницы: 2

Бренд: Thermomart Страницы: 6

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Gemini Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды