Hyster H177 Скачать руководство пользователя страница 15

Страница: 15 / 80

8000 SRM 707

Maintenance Schedule

Table 1. Maintenance Schedule (Continued)

Item

No.

Item

8 hr/

1 day

250

hr/

6 wk

500 hr/

3 mo

1000

hr/

6 mo

2000 hr/

1 yr

Procedure or

Quantity

Specification

Engine Speed
Idle Speed

Mazda M4-2.0G
(Gasoline)

Adjust as

required

700 to 750 rpm

Engine Speed
Idle Speed

Mazda M4-2.2G
(Gasoline)

Adjust as

required

775 to 825 rpm

Engine Speed
Idle Speed

Mazda M4-2.0G
(IMPCO)

Adjust as

required

700 to 750 rpm

Engine Speed
Idle Speed

Mazda M4-2.0 and
2.2G (Aisan Closed
Loop)

Adjust as

required

775 to 825 rpm

Engine Speed
Idle Speed

Mazda M4-2.0 and
2.2G (Aisan Open
Loop)

Adjust as

required

775 to 825 rpm

X=Check C=Change L=Lubricate CIL=Check Indicator Light during operation

NOTE 1:

Check the fuel system for leaks prior to any service or maintenance activity.

NOTE 2:

Change filters on NEW lift trucks at first 100 hours on hourmeter.

NOTE 3:

Very dirty conditions require daily clean and check.

NOTE 4:

Heavy-duty or high-temperature operations require more frequent checks.

NOTE 5:

Cooling indicator light is used only on S40-65XM lift truck models.

NOTE 6:

In dirty or dusty environments, replace at 1000 hours.

NOTE 7:

Perkins engine is to be at operating temperature of 82 ±1.5 C (180 ±35

when inspecting for low

idle setting.

NOTE 8:

Multipurpose grease with 2 to 4% molybdenum disulfide.

NOTE 9:

Mazda M4-2.0G and M4-2.2G 2004 or newer engines, check at 5000 hours or 7 years.

NOTE 10:

Replace on Mazda M4-2.0G and M4-2.2G engines every 2500 hours. Use only hour interval.

NOTE 11:

On Mazda M4-2.0G and M4-2.2G engines, replace the timing belt every 3500 hours. Use only the

hour interval.

NOTE 12:

Perform maintenance as specified by the manufacturer.

Содержание H177

















































































Результаты поиска

Содержание H177

Отзывы:

Похожие инструкции для H177

Бренды по названию

Популярные бренды

Hyster H177, Периодическое техническое обслуживание

Результаты поиска

Содержание H177

Отзывы:

Похожие инструкции для H177

Бренды по названию

Популярные бренды