Hypertherm SmartSYNC 059719 страница 40 Скачать руководство пользователя

Страница: 40 / 98

Prepare to Do the Part Replacement

810460

Service Parts and Procedures

SmartSYNC

Put a clamp on the torch lead

Put the torch on a flat surface so that the left side of the torch handle or shell points up. The left
side of the torch handle is the side with the screws.

Put a clamp on the torch lead to hold the torch in position. Put the clamp 150 mm – 300 mm
(6 inches – 12 inches) from the torch handle or shell.

Figure 1

– 75° hand torch with clamp



This figure shows a 75° hand torch but the procedure is the same for all
torches.

Figure 2

– Full-length machine torch with clamp



This figure shows a full-length machine torch but the procedure is the
same for all torches.

Содержание SmartSYNC 059719



































































































Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Похожие инструкции для SmartSYNC 059719

Бренды по названию

Популярные бренды

Hypertherm SmartSYNC 059719, Руководство по процедурам

Результаты поиска

Содержание SmartSYNC 059719

Отзывы:

Похожие инструкции для SmartSYNC 059719

Бренды по названию

Популярные бренды