HYPERICE Normatec 3, Руководство по эксплуатации

Страница: 10 / 264

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
onctionnement.
INTERNAL BATTERY INFORMATION
This Normatec 3 control unit is equipped with a rechargeable lithium ion battery. The internal
battery is designed to allow use of the Normatec 3 System anywhere—even when power
outlets aren’t available. The Normatec 3 control unit may need to be plugged in before
first use. A fully charged battery will provide power for 2+ hours of continuous use. It takes
approximately 6 hours to fully charge the battery when the control unit is plugged in and not in
use. The rechargeable lithium ion battery is intended to be changed only by authorized service
personnel with the use of a special service tool.
PRODUCT SPECIFICATIONS
• Normatec 3 Model: REJ6
• Normatec 3 Dimensions: 4” (width), 4” (depth), 8.5” (height); [10.2 cm (width), 10.2 cm
(depth), 21.6 cm (height)]
• Normatec 3 Weight: 3.2 lbs [1.45 kg]
• Normatec 3 electrical requirement: 15V DC 1 A
• Maximum Air Pressure: 110 mm Hg
• Temperature (operating): +41° F to 104° F [+5° C to +40° C]
• Temperature (storage): -13° F to +158° F [-25° C to +70° C]
• Relative Humidity (operating): 15% to 93%, non-condensing
• Relative Humidity (storage): -25˚ C without relative humidity control; +70˚ C at relative
humidity up to 93%, non-condensing
• Atmospheric pressure (storage and transportation): 190hPa to 1060hPa
• Atmospheric pressure (operating): 700hPa to 1060hPa
AC-DC ADAPTER
WARNING! Only use the AC-DC adapter model number 30120 provided with the system.
Using a different adapter may cause the system to not operate correctly.
• Input: 100-240V 0.8-0.4 A 50/60 Hz per Normatec 3 model number 60090-
001-00
• Output: 15V DC minimum 1.6 A per Normatec 3 model number 60090-001-00
ELECTROMAGNETIC COMPATIBILITY
The information contained in this section (such as separation distances) is in general
specifically written with regard to the Normatec 3. The numbers provided will not guarantee
faultless operation but should provide reasonable assurance of such. This information may
not be applicable to other medical electrical equipment; older equipment may be particularly
susceptible to interference.
GENERAL NOTES
Medical electrical equipment requires special precautions regarding electromagnetic
compatibility (EMC) and needs to be installed and put into service according to the EMC
information provided in this document and the remainder of the instructions for use of this
control unit.
WARNING!
• Portable RF communications equipment (including peripherals such as antenna
cables and external antennas) should be used no closer than 30 cm (12 inches) to any
part of the Normatec 3, including cables specified by the manufacturer. Otherwise,
degradation of the performance of this equipment could result.
• The Normatec 3 should not be used adjacent to or stacked with other equipment. If
adjacent or stacked use is necessary, the Normatec 3 should be observed to verify
normal operation. If operation is not normal, the Normatec 3 or the other equipment
should be moved.