INLINE MAINTENANCE HEATER WIRING AND OPERATING INSTRUCTIONS
The whirlpool heater is totally self-contained to insure trouble free operation. Once the whirlpool heater is wired,
and the unions are tightened, operation is automatic. The heater will maintain the temperature of the water in the
bathtub. As with all electrical devices, certain safety precautions should be taken during wiring and use. Please
read and follow all these instructions carefully.
FEATURES OF THE INLINE HEATER
Hi-Limit: The whirlpool heater includes an exclusive “Smart Hi-Limit”. This Hi-limit will not “false trip” from hot tap
water. It will only turn the heater off if the thermostat fails. To reset, simply press the red button located on the
heater If the Hi-limit trips frequently, call the factory.
Safety features: In addition to the thermostat and Hi-limit, the whirlpool heater is equipped with a built in pressure
switch. This switch will not allow the heater to turn on if the pump is not running.
CAUTION:
Before use of the pump and heater, test the GFCI for proper operation. The pump and
heater should turn off when the GFCI “TEST” button is pushed. Note: the heater will only operate if the pump is running.
WARNING:
Prolonged immersions in hotter water may induce hypothermia.
Hypothermia occurs when the internal temperature of the body reaches a level several degrees above the normal
body temperature of 98.6 degrees F. The symptoms of hypothermia include an increase in the internal temperature
of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hypothermia include (1) failure to perceive
heat (2) failure to recognize the need to exit the whirlpool (3) Unawareness of impending hazard (4) fetal damage in
pregnant women (5) physical inability to exit whirlpool (6) Unconsciousness resulting in the danger of drowning.
WARNING:
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hypothermia
OPTIONAL UNDERWATER LIGHT AND CHROMATHERAPY MOOD LIGHTING:
Operation:
UNDERWATER LIGHT: Press the on/off button once to turn on light; Press it again to turn off the light
CHROMATHERAPY:
Press the button and the light turns on
1st press starts fast cycle off all colors
2nd press turns off
3rd press is the CLEAR color
4th press turns off
5th press is the GREEN color
6th press turns off
7th press is the YELLOW color
8th press turns off
9th press is the BLUE color
10th press turns off
11th press is the RED color
12th press turns off
13th press is the GREEN color
14th press turns off
15th press is the VOILET color
16th press turns off
17th press is BLUE to GREEN to BLUE
18th press turns off
19th press is RED to YELLOW to VOILET
20th press turns off
21st press fast cycle starts over
TO REPLACE THE BULB:
Disconnect the power to the bathtub.
Drain the bathtub.
Open the lens of the fixture using only the proper tool provided for that purpose.
Do not attempt to replace bulb without the proper tool. If a tool was not
provided, stop here and contact the factory.
Use only a type 912 replacement lamp.
Verify “O” ring is not damaged and is properly positioned in the groove when
replacing the lens. If there is damage or lens does not seal properly, do not
refill bathtub. Contact factory immediately.
NOTE: DO NOT TWIST BULB INTO SOCKET
.
Use gentle pressure and push bulb into place.
11
16.
Hi-Limit: Some whirlpool heaters include an exclusive “Smart Hi-Limit”. This Hi-limit will not “false trip” from hot tap
water. It will only turn the heater off if the thermostat fails. To reset, simply press the red button located on the heater.
If the Hi-limit trips frequently, call the factory.
hyperthermia.
Hyperthermia
hyperthermia
hyperthermia
hyperthermia
