Hydralok H19MM Скачать руководство пользователя страница 6

Страница: 6 / 15

TECHNICAL / DIMENSIONAL DATA

H19MM

Capacity

3/16

” – 3/4” (2 wire)

R1AT, R2AT, 1SN, 2SN

Pressure requirements for optional

air/hydraulic power pack

7.0 bar (100 psi)

Packed Dimensions [mm]

600x400x460

Net weight [kg]

Type of operation

Twin speed hand pump

(10.000 psi)

Noise level

< 70 dB

HANDLING / TRANSPORT

The machine will normally be shipped bolted to a wooden pallet. The bolts should be
removed and the machine lifted onto the work place using suitable lifting equipment.

PRELIMINARY CHECKS

Place the machine on a stable surface.

LIGHTING

The equipment does not have its own lighting and so it must be used in a suitably
illuminated area.

ROUTINE MAINTENANCE

Ensure that moving parts are always lightly greased. Where applicable check periodically

that the limit switches and emergency controls are in good working order.

Содержание H19MM
















Результаты поиска

Содержание H19MM

Отзывы:

Похожие инструкции для H19MM

Бренды по названию

Популярные бренды

Hydralok H19MM, Руководство пользователя

Результаты поиска

Содержание H19MM

Отзывы:

Похожие инструкции для H19MM

Бренды по названию

Популярные бренды