Hydralok H19MM Скачать руководство пользователя

Страница: 5 / 15

SAFETY REGULATIONS

Always work in safe conditions and with the necessary space around the machine. Ensure
that the machine is placed on a stable and appropriate working surface.

1. DO NOT USE the equipment before reading the user manual.

2. CAUTION! If improperly used, the equipment may be dangerous and may cause

injury. Do not touch any moving parts.

3. CAUTION! It is absolutely essential that all working operations are carried out

one operator only

4. This manual must be provided for the machine operator. Ensure that the operator is

aware of his/her responsibilities.

5. Guards must never be removed or tampered with.

6. (Where applicable) A fully trained and competent electrician must connect the

machine to the appropriate electricity supply.

7. Always wear protective gloves, safety glasses and appropriate clothing.

8. (Where applicable) Disconnect the power supply before removing any covers, or

attempting any maintenance of the machine

Only original spare parts can be used in the maintenance of the machine.

Содержание H19MM
















Результаты поиска

Содержание H19MM

Отзывы:

Похожие инструкции для H19MM

Бренды по названию

Популярные бренды

Hydralok H19MM, Руководство пользователя

Результаты поиска

Содержание H19MM

Отзывы:

Похожие инструкции для H19MM

Бренды по названию

Популярные бренды