background image

Level/Speed

Control
Voltage

(V)

10

10 (Ω)

9

9 (Ω)

8

8 (Ω)

7

7 (Ω)

6

6 (Ω)

5

5 (Ω)

4

4 (Ω)

3

3 (Ω)

2

1.5 (Ω)

1

500 (Ω)

0

1 (Ω)

Please note: This is an estimated 
adjustment guide

149-CD-POT

149-CD-POT

The 149-CD-POT is a commissiong device designed to be used with our EC range of fans.

This device will be as standard with our box fan range from May 2018.

The device will allow the for the installer to set the maximum operating speed of the fan that it is
connected to.

The installer or commissioning engineer can adjust the fan speed using the potentiometer built onto the

149-CD-POT board. This potentionmeter can either be used for single speed adjustment or to set a
maximum speed for the fan to operate at when an external control source is used.

If external speed control is required, the jumper connection next to the potentionmeter on the board
would need to be removed, the installer can then connect to ST1 (using the diagram provided).

When an external speed control is fitted, the maximum speed setting available to the external control is
limited by the potentiometer setting of the commissioning device.

10/07/2018

MK-149-CD-POT

Issue:

Saved Date:

A

The 149-CD-POT is a commissiong device designed to be used with our 
EC range of fans.
The device will allow the for the installer to set the maximum operating speed 
of the fan that it is connected to.
The installer or commissioning engineer can adjust the fan speed using the 
potentiometer built onto the 149-CD-POT board.
This potentiometer can either be used for single speed adjustment or to set 
a maximum speed for the fan to operate at when an external control source 
is used.
If external speed control is required, the jumper connection next to the 
potentiometer on the board would need to be removed, the installer can 
then connect to ST1 (using the diagram provided).
When an external speed control is fitted, the maximum speed setting 
available to the external control is limited by the potentiometer setting of 
the commissioning device.

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03.

149-CD-POT Issue A: 10.07.2018
Check the individual product accessories table for fan controller compatibility.

Содержание HXP EC









Отзывы: