HYDAC FILTER SYSTEMS CTM-EF 3 3 Series Скачать руководство пользователя страница 45

Страница: 45 / 64

HYDAC FILTER SYSTEMS GMBH

Operation | 6

BeWa CTM-EF3x3x 4436386 en-us lq

45 / 64

6.5 Conducting the extraction

WARNING

Brush discharge/corona discharge

Bodily injury due to the ignition of an explosive atmosphere.

Connect the test item to a potential-free earth.

The test item hoses are to be connected to the

test item

to be analyzed

according to the information given in the previous chapters.

The test item is connected to the grounding connection.

1. Enter the required analysis parameters in the user interface of the

CTM-SC module and then press the button and the foot switch (depend-

ing on the software setting). The CTM-SC supply module pumps the test

liquid into the receiver tank, via the selected port and the test item.

2. The test liquid (now called the

analysis fluid

) carrying the particulate con-

tamination flushed off the component, is sucked through the filter mem-

brane, with the help of a membrane pump, via connection R and flows

back to the CTM-SC supply module.

The membrane pump will continue running once extraction is complete.

The message "… Pause … wait until test liquid has been extracted" will

appear on the user interface.

3. Remove the test liquid from the test item.

4. Once the test liquid has been fully extracted, press the button on the user

interface.

5. Remove the filter membrane from the filter membrane holder in order to

analyze it.

The extraction is complete.

6.5.1 Changing the direction of flushing

The primary flushing direction, from the extraction device through the test item,
is from port A‘ -> R‘. You can reverse this flushing direction R‘ -> A‘. via the user
interface.

6.5.2 Draining the test item

Certain test items cannot be fully drained of the test liquid after extraction. For
details, see …

Содержание CTM-EF 3 3 Series

































































Результаты поиска

Содержание CTM-EF 3 3 Series

Отзывы:

Похожие инструкции для CTM-EF 3 3 Series

Бренды по названию

Популярные бренды

HYDAC FILTER SYSTEMS CTM-EF 3 3 Series, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание CTM-EF 3 3 Series

Отзывы:

Похожие инструкции для CTM-EF 3 3 Series

Бренды по названию

Популярные бренды