Hy-Security SwingRiser 14 Скачать руководство пользователя | Manualshive

Страница: 60 / 86

background image

Installation and Maintenance Manual

50

24Hr / 7 Day Time Clock Option

This is an option you can order from HySecurity. The timer generates an open command which will hold
the gate open until it is released. Instructions on how to use and program it accompany the timer.

To connect the optional timer to the Smart Touch Controller, use the following schematic:

Connect the Timer Power Pin 1 to 24V (+)

Connect the Timer Power Pin 2 to COM

Connect the Timer Com Pin 3 to COM

Connect Timer NO Pin 4 to #7, Time Clock Open

Connecting a Radio Receiver

Mount a commercial style 24 Volt radio receiver (external antenna type) on the inside of the operator,
below the electrical box. Knock out the smallest hole in the lower right corner of the electrical box and
route the wires to the area marked Radio Options. Only three wire connections are needed because the
24-Volt supply and the radio output share a wire. Being certain to observe polarity, crimp the black radio
power wire together wit

h one of the radio output wires into a .25‖ spade connector and connect to the

COM terminal.

Connect the red wire to the
+24V terminal and connect the
other radio output contact wire
to the spade marked OPEN.

Note that this terminal is the
same as the #4 input terminal
labeled Edge Sensor on the
main control board.

Mount an external antenna
onto the top of a fixed post of
the fence near the operator.

Connect the antenna into the
socket on the radio receiver.

Set the DIP switches in the
receiver to match the same
code used in the transmitter.

If an edge sensor transmitter is connected, be certain to use a two channel commercial receiver.
Remember that each transmitter and receiver must have their codes set the same or they will not
function.

«
...
58
59
60
61
62
...
»

Содержание SwingRiser 14























































































Отзывы:

Нет отзывов

Похожие инструкции для SwingRiser 14

Бренд: PAC Страницы: 6

Бренд: Genie Страницы: 2

Бренд: Genius Страницы: 22

Бренд: GTO Страницы: 45

Бренд: ECOSTAR Страницы: 40

Merlin Whisper Drive MT3850

Бренд: Chamberlain Страницы: 32

Бренд: Nice Страницы: 148

Бренд: Supeero Страницы: 8

Бренд: CAME Страницы: 22

Бренд: Chamberlain Страницы: 40

Бренд: Xtreme Garage Страницы: 2

Бренд: CAME Страницы: 24

VER-PLUS Series

Бренд: CAME Страницы: 36

Бренд: Continental Refrigerator Страницы: 4

Бренд: Chamberlain Страницы: 36

Бренд: Roger Technology Страницы: 16

Бренд: FAAC Страницы: 10

Бренд: FAAC Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды