Hwayuan Electric ZX7-315IGBT Скачать руководство пользователя страница 11

Страница: 11 / 12

ZX7-315/400/500/630IGBT OPERATOR’S MANUAL

- 11 -

Suddenly there is no welding
current during the welding
process

1.welding cable and work piece
with poor connection
2.Protective fuse break

1.check the weld cable
2.Replace the fuse(1.5A)

Machine not work, but the
overload indicator on

1. Cooling fan damaged cause
overheat protection
2. Over-load use cause over heat
protection

1. Replace cooling fan
2. Stop welding, let the machine
operate for 10min without load

Machine not work, but the lack
voltage indicator on

The input lack-phase or lack voltage

Check three phase input

Attention

: Only qualified technicians should perform troubleshooting work on the machine. If for any

reason you do not understand the test procedures or are unable to perform the tests/repairs safely, please
contact us for technical assistance.

11 Packing List

1. ZX7-IGBT welding machine

1 set

2 . Electrode holder

1 pcs

3. Fast connector

2 pcs

4..Documents (Guarantee card, operatoer's manual, quality certificate)

1 for each

Содержание ZX7-315IGBT













Результаты поиска

Содержание ZX7-315IGBT

Отзывы:

Похожие инструкции для ZX7-315IGBT

Бренды по названию

Популярные бренды

Hwayuan Electric ZX7-315IGBT, Руководство оператора

Результаты поиска

Содержание ZX7-315IGBT

Отзывы:

Похожие инструкции для ZX7-315IGBT

Бренды по названию

Популярные бренды