manualshive.com logo in svg

HUSTLER ATZ, Руководство оператора, Страница: 21 / 48

Поделиться
Скачать
HUSTLER ATZ Скачать руководство пользователя страница 21

604243

3-7

REV C

A ROPS when used with a seat belt can minimize injuries 

during unit overturn accidents. Figure 3-7            

Seat belt maintenance

Inspect the seat belt system (all seat, seat belt parts, seat pan 

and seat pan latch) daily prior to mowing for signs of any 
damage. These parts should be replaced if any parts indicate 
signs of:

• cuts
• fraying
• extreme or unusual wear
• significant discoloration due to UV exposure
• dirt or stiffness
• abrasion to the seat belt webbing
• damage to the buckle, latch plate or hardware.
• any other problem

If the seat belt is to be cleaned, use soap and water. Do not use 

carbon tetrachloride, naphtha, or other chemical cleaning 
agents, as these will weaken the webbing. For the same reason, 

do not bleach or dye the webbing. Replace the seat belt if worn 
or damaged.

Possible damage to ROPS

If the unit has rolled over or the ROPS has been in some other 

type of accident (such as hitting an overhead object during 
transport), the ROPS must be replaced to retain the best 
protection.

Following an accident, check the ROPS, the operator’s seat, 

the seat belt, seat belt mountings and seat latch for possible 
damage. Before operating the machine, replace all damaged 
parts. 

IMPORTANT:  

Do not attempt to weld or straighten the 

ROPS.   

ROPS Inspection

Inspect the ROPS after the first 20 hours of operation. 

Following the initial inspection, check the ROPS after every 500 
hours of operation or every six months, whichever comes first. 

1.

Check the torque of the ROPS mounting bolts. Tighten 
the bolts to the correct torques as shown below if 
necessary. Figure 3-8

2.

Inspect the operator’s seat and the mounting parts for the 
seat belt. Tighten the bolts to the correct torque as shown 
below if necessary and replace parts that show wear or 
damage.

3.

Check the seat latch to make sure it is secured and 
functioning properly. Adjust or repair it as necessary.

Torque values are given below:

Ft-lbs.

N-m

ROPS mounting bolts  . . . . . . . . . . . . . . . . . . . . .  73 . . . . 99
Seat belt mounting hardware . . . . . . . . . . . . . . . .  48 . . . . 65

WARNING

Always pull from the mower hitch. Do not attach chains 
or ropes to the ROPS for pulling purposes, as the machine 
can tip backwards.

Figure 3-7

ROPS

WARNING

The ROPS structure’s protective capability may be 
impaired by structural damage, overturn or altera-
tion.

 Do not remove or alter any of the ROPS parts. Do 

not attempt to weld or straighten ROPS. Failure to adhere 
to these instructions could result in severe injury or death.
If the ROPS or cab is replaced, make sure that the proper 
hardware is used and the recommended torque values are 
applied to the attaching bolts.

WARNING

Never operate the mower with the seat latch un-installed 
and improperly secured. The seat platform must be 
securely latched to prevent seat from moving/tilting in the 
event of mower tipping or rollover.

Содержание ATZ

















































Отзывы:

Нет отзывов