background image

Frozen Meat and Seafood

P/N 424382A

1-1

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 (Printed in U.S.A.)

NSF CERTIFICATION

These merchandisers are manufactured to meet
ANSI / National Sanitation Foundation (NSF

®

)

Standard #7 requirements. Proper installation is
required to maintain certification. Near the serial
plate, each case carries a label identifying the type
of application for which the case was certified.

ANSI/NSF-7 Type I – Display Refrigerator / Freezer

Intended for 75°F / 55%RH Ambient Application

ANSI/NSF-7 Type II – Display Refrigerator / Freezer

Intended for 80°F / 55%RH Ambient Application

ANSI/NSF-7 – Display Refrigerator 

Intended for Bulk Produce

LOCATION

These merchandisers are designed for displaying
products in air conditioned stores where tempera-
ture is maintained at or below the ANSI/NSF-7
specified level and relative humidity is maintained
at or below 55%. 

Placing refrigerated merchandisers in direct sun-
light, near hot tables or near other heat sources
could impair their efficiency.

Like other merchandisers, these are sensitive to air
disturbances. Air currents passing around merchan-
disers will seriously impair their operation. Do
NOT allow air conditioning, electric fans, open
doors or windows, etc. to create air currents around
the merchandisers.

Product should always be maintained at proper
temperature. This means that from the time the
product is received, through storage, preparation
and display, the temperature of the product must
be controlled to maximize the life of the product.

SHIPPING DAMAGE

All equipment should be thoroughly examined for
shipping damage before and during unloading.

This equipment has been carefully inspected at our
factory. Any claim for loss or damage must be
made to the carrier. The carrier will provide any
necessary inspection reports and/or claim forms.

Apparent Loss Or Damage

If there is an obvious loss or damage, it must be
noted on the freight bill or express receipt and
signed by the carrier’s agent; otherwise, carrier
may refuse claim. 

Concealed Loss Or Damage

When loss or damage is not apparent until after
equipment is uncrated, retain all packing materials
and submit a written request to the carrier for
inspection, within 15 days.

EXTERIOR LOADING

Do NOT walk on top of merchandisers

or 

damage to the merchandisers and serious personal
injury could occur. T

HEY ARE NOT STRUCTURALLY

DESIGNED

TO

SUPPORT

EXCESSIVE

EXTERNAL

LOADING

such as the weight of a person. Do not

place heavy objects on the case.

INSTALLATION

Do not walk or put heavy objects on case.

CAUTION

!

Содержание Impact F2






























Отзывы: