Hussmann Chino MPC-ET Series, Руководство по установке и эксплуатации

Страница: 7 / 20

7
Parameter Programmed Report
Parameter Description Value Min Max
1 Freezer Cut-in warm 32°F -40ºC (-40ºF) 40ºC (104ºF)
2 Freezer Cut-out warm 28°F -40ºC (-40ºF) 40ºC (104ºF)
3 Freezer Cut-in cold 22°F -40ºC (-40ºF) 40ºC (104ºF)
4 Freezer Cut-out cold 18°F -40ºC (-40ºF) 40ºC (104ºF)
5 Compressor ON time delay at Controller Power Up 0 min 0 sec 0 sec 59 min 59 sec
6 Compressor Minimum (ON) time 4 min 0 sec 0 sec 30 min 59 sec
7 Compressor Minimum (OFF) time 0 min 30 sec 0 sec 59 min 59 sec
8 Potentiometer off position 10º 5º 57º
9 Potentiometer on position 15º 9º 61º
10 On-Off logical function 1
11 Controller Operation Temperature Units 1
12 Sensor failure mode
(compressor and fan relay
failure mode)
3
13 Compressor On Time if Sensor failed 0 hour 6 min 1 min 59 hour 59 min
14 Compressor Off Time if Sensor failed 0 hour 2 min 1 min 59 hour 59 min
15 Defrost Function 1
16 Defrost Method 2
17 Time to first defrost(Initial frost build time) 2 hour 0 min 10 min 71 hour 59 min
18 Time to subsequent defrost 4 hour 0 min 10 min 71 hour 59 min
19 Defrost duration Time (failsafe) 0 hour 30 min 1 min 4 hour 59 min
20 Defrost Termination temperature 50°F -40ºC (-40ºF) 40ºC (104ºF)
21 Drip time 0 min 0 sec 0 sec 59 min 59 sec
22 Defrost Cycle at power on 0
23 Evaporator Temp. Sensor 1
24 Defrost Termination Method 2
25 Temperature Initiated Defrost Function 1
26 Temperature Initiated Defrost (T = Tspace-Tevap.) 4°F 0ºC (0ºF) 40ºC (72ºF)
27 Temperature Initiated Defrost Time Delay 3 min 0 sec 0 sec 59 min 59 sec
28 Temperature Initiated Defrost Time Delay
After Defrost
30 min 0 sec 0 sec 59 min 59 sec
29 Temperature Alarm Enable 1
30 High Temperature Alarm - Warm 42°F -40ºC (-40ºF) 40ºC (104ºF)
31 Low Temperature Alarm - Warm 24°F -40ºC (-40ºF) 40ºC (104ºF)
32 High Temperature Alarm - Cold 34°F -40ºC (-40ºF) 40ºC (104ºF)
33 Low Temperature Alarm - Cold 16°F -40ºC (-40ºF) 40ºC (104ºF)
34 Temperature Alarm Differential 4°F 1ºC (2ºF) 10ºC (18ºF)
35 Temperature Alarm Time delay 0 hour 30 min 0 min 4 hour 59 min
36 Temperature Alarm Disable Time after Start Up 2 hour 0 min 0 min 17 hour 59 min
37 Temperature Alarm Delay after Defrost 1 hour 0 min 0 min 17 hour 59 min
38 Buzzer Function 1
39 Buzzer Period 24.9 sec 0.2 sec 24.9 sec
40 Led Alarm Function 1
41 Led Alarm Period 2.0 sec 0.4 sec 24.8 sec
42 Defrost Display Lock
(display indication during defrost)
1
43 Sensor Fault Monitoring Time 1 min 0 sec 5 sec 59 min 59 sec
44 Display Temperature Offset 0°F -40ºC (-72ºF) 40ºC (72ºF)
45 Display Unlock Time 0 hour 10 min 0 min 1 hour 59 min
46 Show Parameter Code Number 1
47 Parameter Code Number 6 0 99
48 Maximum Compressor Run Function 0
49 Maximum Compressor Run Time 2 hour 0 min 0 min 17 hour 59 min
50 Defrost Heater Duty Cycle Function 0
51 Heater On Time 1 min 0 sec 5 sec 59 min 59 sec
52 Heater Off Time 0 min 30 sec 0 sec 59 min 59 sec
0=display temperature read
1=lock the display on temp.
2=display DF
0=disable or 1=enable
0=disable or 1=enable
0=disable or 1=enable
0=disable or 1=enable
0=disable
1=Evap. Sensor
2=Control Sensor
3=Digital Switch (close)
0=disable or 1=enable
0=disable or 1=enable
0=disable or 1=enable
0=disable or 1=enable
0=disable or 1=enable
0=Celsius or 1=Fahrenheit
0=Relays fail OPEN
2=Relays fail CLOSE
3=Duty cycle
0=disable
1=System run time
2=Compressor run time
1=Electric
2=Off-cycle
3=reverse cycle
0=disable or 1=enable
8/20/2015 MPC-ET-8S_Report.xls
Safenet III Programmed Parameters