background image

16

User Information

Stocking

Improper  temperature  and  lighting  will  cause  serious 
product  loss.  Discoloration,  dehydration  and  spoilage 
can be controlled with proper use of the equipment and 
handling of product. Product temperature should always 
be  maintained  at  a  constant  and  proper  temperature. 
This  means  that  from  the  time  the  product  is  received, 
through storage, preparation and display, the temperature 
of the product must be controlled to maximize life of the 
product. Hussmann cases were not designed to “heat up” 
or “cool down” product - but rather to maintain an item’s 
proper temperature for maximum shelf life. To achieve the 
protection required always:

1.   Minimize processing time to avoid damaging 

temperature rise to the product. Product should be 
at proper temperature.

2.   Keep the air in and around the case area free 

of foreign gasses and fumes or food will rapidly 
deteriorate.

3.   Maintain the display merchandisers temperature 

controls as outlined in the refrigerator section of this 
manual.

4.   Do not place any product into these refrigerators 

until all controls have been adjusted and they 
are operating at the proper temperature. Allow 
merchandiser to operate a minimum of 6 hours 
before stocking with any product.

5.   When stocking, never allow the product to extend 

beyond the recommended load limit. 

Air discharge 

and return air 

fl ow must be unobstructed at all 

times to provide proper refrigeration.

6.  Keep the service doors closed (when applicable). 

Refrigeration performance will be seriously affected 
if left open for a prolonged period of time.

7.   Avoid the use of supplemental fl ood or spot lighting. 

Display light intensity has been designed for 
maximum visibility and product life at the factory. 
The use of higher output LED lamps (H.O. and 
V.H.O.), will shorten the shelf life of the product.

Evaporator Fans

The evaporator fans are located at the center front of these 
merchandisers directly beneath the display pans. 

Should 

fans or blades need servicing, always replace fan blades 
with the raised embossed side of the blade TOWARD THE 
MOTOR.

Copper Coils

The copper coils used in Hussmann merchandisers may 
be repaired in the 

fi eld. Materials are available from local 

refrigeration wholesalers.

Hussmann recommends using #15 Sil-Fos for repairs.

Aluminum Coils

The aluminum coils should be replaced if damaged.

Non-Glare Glass (Optional)

The  high  optical  clarity  of  this  glass  is  possible  due  to 
special coatings on the glass surface itself. To preserve this 
coating and the optical clarity, keep the glass clean.

Water  is  the  only  solution  recommended  to  be  used  to 
clean the non-glare glass. The damage to the glass from 
improper, caustic solutions is irreparable.

In  addition  to  cleaning  the  glass  with  the  recommended 
product, there are precautions that should be taken when 
working and cleaning the inside of the case.

•   When cleaning the inside of the cases, we 

recommend that the glass be fully opened and 
covered to prevent to prevent solutions from 
splashing onto the glass and ruining the coating on 
the inside.

•   Only use a soft cloth and water (in a spray bottle) for 

cleaning any glass or mirrored components. Be sure 
to rinse and/or dry completely.

•  

Never use hot water on cold glass surfaces! 
It may shatter and cause serious injury! 

Allow 

glass surfaces to warmed to room temperature.

Plexiglass and Acrylic Care

Improper cleaning not only accelerates the cleaning cycle 
but also degrades the quality of this surface. Normal daily 
buffi ng motions can generated static cling attracting dust 
to the surface. Incorrect cleaning agents or cleaning cloths  
can  cause  micro  scratching  of  the  surface,  causing  the 
plastic to haze over time.

Cleaning

Hussmann recommends using a clean damp chamois, or a 
paper towel marketed as dust and abrasive free with 

210

®

 

Plastic Cleaner and Polish

 available by calling Sumner 

Labs at 

1-800-542-8656

. Hard, rough cloths or paper towels 

will scratch the acrylic and should not be used.

Antistatic Coatings

The product 

210

®

 has proven to be very effective in not 

only cleaning and polishing the Plexiglass surface, but also  
providing anti-static and anti-fog capabilities. This product 
also seals pores and provides a protective coating.

Tips and Troubleshooting
Before calling for service, check the following:

1.   Check electrical power supply to the equipment for 

connection.

2.   Check fi xture loading. Overstocking case will affect 

its proper operation.

3.   If frost is collecting on fi xture and/or product, check 

that no outside doors or windows are open allowing 
moisture to enter store. These merchandisers were 
designed for use in stores were temperature & 
humidity does not exceed 75° F and 55% H.

4.   If front self-service case is not performing check 

proper installation of lower deck pan refer to case 
cleaning section.

Содержание CR3HV-F































Отзывы: