background image

17

User Information (Cont'd)

the front glass is “lift up glass” and is NOT sealed. IT 
WILL LEAK.) Keep all water within the base of the 
case.

3.   Apply the sanitizing solution according to the 

manufacturer’s directions.

4.   Rinse thoroughly.
5.   Dry completely before resuming operation.

                          

CLEANING PRECAUTIONS

When cleaning:

• Do not use high pressure water hoses
• Do not introduce water faster than waste outlet can drain
• NEVER ON A SELF CONTAINED UNIT WITH AN EVAPORATOR FAN
• NEVER USE A CLEANING OR SANITIZING SOLUTION THAT HAS AN OIL 
   BASE (these will dissolve the butyl sealants) or an AMMONIA BASE 
    (this will corrode the copper componets of the case)

To preserve the attractive finish:

• DO USE WATER AND A MILD DETERGENT FOR THE EXTERIOR ONLY
• DO NOT USE ABRASIVES OR STEEL WOOL SCOURING PADS  
   (these will mar the finish)

Case Cleaning

Long life and satisfactory performance of any equipment 
are dependent upon the care given to it. To insure long life, 
proper  sanitation  and  minimum  maintenance  costs,  the 
refrigerator should be thoroughly cleaned frequently.

SHUT OFF FAN DURING CLEANING PROCESS. It can be 
unplugged within the case, or shut off case at the source. 
The  interior  bottom  may  be  cleaned  with  any  domestic 
soap  or  detergent  based  cleaners.  Sanitizing  solutions 
will not harm the interior bottom, however, these solutions 
should  always  be  used  according  to  the  manufacturer’s 
directions.

It is essential to establish and regulate cleaning procedures. 
This  will  minimize  bacteria  causing  discoloration  which 
leads  to  degraded  product  appearance  and 

signifi cantly 

shortening product shelf life.

Soap and hot water are NOT enough to kill this bacteria. A 
sanitizing solution MUST be included with each cleaning 
process to eliminate this bacteria.

Remove all food stuffs, ice, debris, etc., and either access 
the case from the rear or the front of the case. Allow the 
case to come to room temperature.

1.   Scrub thoroughly, cleaning all surfaces, with soap 

and hot water.

2.   Rinse with hot water, but DO NOT fl ood or spray 

glass. (If you are working from the rear of the case, 

Содержание CR3HV-F































Отзывы: