Husqvarna YTH2754T Скачать руководство пользователя

Страница: 25 / 36

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 40)

WARNING:

Do not short battery ter mi nals by allowing

a wrench or any other object to contact both terminals at

the same time. Before connecting battery, remove metal

bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent spark-

ing from ac ci den tal grounding.
• Lift hood to raised position.
•

Disconnect BLACK battery cable (A) then RED battery

cable and carefully remove battery from tractor.

• Install new battery with terminals in same position as

old battery.

•

First connect RED battery cable (B) to positive (+) battery

terminal with hex bolt and keps nut as shown. Tighten

securely. Slide terminal cover (C) over terminal.

•

Connect BLACK grounding cable to negative (-) bat tery

terminal with re main ing hex bolt and keps nut. Tight en

securely

• Close

hood.

Positive

(Red)

Cable

Negative (Black)

Cable

02954

Fig. 40

TO REPLACE HEADLIGHT BULB

• Raise

hood.

• Pull bulb holder out of the hole in the backside of the

grill.

• Replace bulb in holder and push bulb holder securely

back into the hole in the backside of the grill.

• Close

hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run

poorly, stop running, or prevent it from starting.
• Check wiring.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The

fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY

(See Fig. 41)

• Raise

hood.

• Unsnap headlight wire connector.
•

Stand in front of tractor. Grasp hood at sides, tilt toward

engine and lift off of tractor.

• To replace, reverse above procedure.

03076

HEADLIGHT

WIRE

CONNECTOR

HOOD

ENGINE

TO AD JUST THROTTLE CON TROL CABLE

The throttle control has been preset at the factory and

ad just ment should not be necessary. If adjustment is nec-

es sary, see engine manual.

TO AD JUST CHOKE CON TROL

The choke control has been preset at the factory and ad-

just ment should not be necessary. If adjustment is neces-

sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not

operate properly due to suspected carburetor problems,

take your tractor to an authorized service center for repair

and/or adjustment.

Fig. 41

Содержание YTH2754T





































Результаты поиска

Содержание YTH2754T

Отзывы:

Похожие инструкции для YTH2754T

Бренды по названию

Популярные бренды

Husqvarna YTH2754T, Руководство оператора

Результаты поиска

Содержание YTH2754T

Отзывы:

Похожие инструкции для YTH2754T

Бренды по названию

Популярные бренды