background image

2 Safety

2.1 Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of injury or

death for the operator or bystanders if the

instructions in the manual are not obeyed.

CAUTION: Used if there is a risk of damage to

the product, other materials or the adjacent area

if the instructions in the manual are not obeyed.

Note: Used to give more information that is necessary in

a given situation.

2.2 General safety instructions

WARNING: Read the warning instructions that

follow before you use the product.

The service center that repairs the product must have

safety devices that obey local regulations. Warnings and

cautions are used to point out specially important parts

of the workshop manual.

2.3 Special safety instructions

Stop the engine, remove the spark plug and let the

engine become cool before maintenance.

Do not start the product indoors or in areas that do

not have sufficient airflow. The exhaust fumes from

the engine contain carbon monoxide which is an

odorless, poisonous and very dangerous gas.

Do not start the product near flammable materials.

The exhaust fumes from the engine are hot and can

contain sparks which can start a fire.

Keep all body parts away from hot surfaces, or high

voltage lead.

Do not put the product or a fuel container near warm

objects, an open flame, a spark or a pilot light.

2.3.1 Fuel safety

WARNING: Read the warning instructions that

follow before you use the product.

Fuel is flammable and the fumes are explosive. Be

careful with fuel to prevent injury, fire and explosion.

Do not breathe in the fuel fumes. The fuel fumes are

poisonous and can cause injury. Make sure that the

airflow is sufficient.

Do not remove the fuel tank cap or fill the fuel tank

when the engine is on.

Let the engine become cool before you refuel.

Do not fill fuel in an indoor area. Not sufficient airflow

can cause injury or death because of asphyxiation or

carbon monoxide.

Do not smoke near the fuel or the engine.

Do not put hot objects near the fuel or the engine.

Do not fill fuel near sparks or flames.

Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

Fuel on your skin can cause injury. If you get fuel on

your skin, use soap and water to remove the fuel.

If you spill fuel on your clothing, change clothing

immediately.

Do not fill the fuel tank fully. Heat causes the fuel to

expand. Keep a space at the top of the fuel tank.

Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

Before you start the product, move the product to a

minimum of 3 m/10 ft from where you refueled.

Do not start the product if there is fuel or engine oil

on the product. Remove the unwanted fuel and

engine oil and let the product dry before you start

the engine.

Examine the engine for leaks regularly. If there are

leaks in the fuel system, do not start the engine until

the leaks are repaired.

Do not use your fingers to examine the engine for

leaks.

Keep fuel in approved containers only.

When the product and fuel is in storage, make sure

that fuel and fuel fumes cannot cause damage.

Drain the fuel in an approved container outdoors and

away from sparks and flames.

2.4 Symbols on the product

WARNING! This product can be

dangerous and cause serious injury or

death to the operator or others. Be careful

and use the product correctly.

Read the operator's manual carefully and

make sure that you understand the

instructions before use.

Stop the engine and remove the ignition

cable before repairs or maintenance.

Fuel.

Oil level.

Risk of fire.

4 - Safety

1425 - 001 - 03.06.2020

Содержание HS 139A

















































Отзывы: