Husqvarna HS 139A Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 48

background image

6.3 Air filter

6.3.1 To remove and install the air filter

WARNING: Use protective gloves.

1. Push the clips on the air filter cover.
2. Carefully remove the air filter cover (A) from the

engine.

3. Remove the air filter (B).

A

B

4. Examine the air filter for damages. Replace a

damaged air filter.

5. Clean and examine the air filter. Refer to

the paper filter on page 20.

6. Install in the opposite sequence.

6.3.2 To clean the paper filter

1. Remove the air filter cover and remove the paper

filter.

2. Hit the filter against a flat surface to make the

particles fall off.

CAUTION: Do not use solvent or

compressed air to clean the paper filter.

3. Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

4. Put the air filter cover back.

6.3.3 To remove and install the air filter holder

WARNING: Use protective gloves.

1. Remove the air filter. Refer to

To remove and install

the air filter on page 20.

2. Remove the 2 nuts and remove the air filter holder.

3. Install in the opposite sequence.

20 - Repair instructions

1425 - 001 - 03.06.2020

«
...
18
19
20
21
22
...
»

Содержание HS 139A

















































Отзывы:

Нет отзывов

Похожие инструкции для HS 139A

Бренд: Wacker Neuson Страницы: 44

Бренд: V2 Страницы: 20

Бренд: Westerbeke Страницы: 65

Бренд: Beninca Страницы: 72

Бренд: Lenze Страницы: 20

Бренд: Deutz Страницы: 257

Бренд: Perkins Страницы: 27

Бренд: O.S. engine Страницы: 4

Бренд: DLE Страницы: 4

Бренд: Clarke Страницы: 41

Бренд: O.S. Speed Страницы: 4

Бренд: Mitsubishi Heavy Industries Страницы: 156

Бренд: Dietz Страницы: 12

Бренд: Toyota Страницы: 193

Бренд: AWE Tuning Страницы: 4

Бренд: SABB MOTOR Страницы: 142

Бренд: Mitsubishi Страницы: 42

Бренд: YASKAWA Страницы: 177

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды