Husqvarna F2303U4 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 169

background image

12 SERVICE WORK ON THE CHASSIS

80

12.34

Cleaning the chain

Warning

Danger of accidents

Lubricants on the tires reduces the road grip.

–

Remove lubricants from the tires using a suitable cleaning agent.

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Info

The service life of the chain depends largely on its maintenance.

Preparatory work

–

Raise the motorcycle with a lift stand. (

400725-01

Main work

–

Rinse off loose dirt with a soft jet of water.

–

Remove old grease residue with chain cleaner.

Chain cleaner (

–

After drying, apply chain spray.

Off-road chain spray (

Finishing work

–

Remove the motorcycle from the lift stand. (

12.35

Checking the chain tension

Warning

Danger of accidents

Incorrect chain tension damages components and results in accidents.

If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear
wheel bearings wear more quickly. Some components may break if overloaded.
If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket. As a result, the
rear wheel locks or the engine will be damaged.

–

Check the chain tension regularly.

–

Set the chain tension in accordance with the specification.

Preparatory work

–

Raise the motorcycle with a lift stand. (

«
...
80
81
82
83
84
...
»

Содержание F2303U4










































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2303U4

Бренд: Yamaha Страницы: 102

Бренд: R&G Страницы: 9

Бренд: TVS Страницы: 60

Бренд: Baja motorsports Страницы: 66

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 176

Бренд: hepco & becker Страницы: 3

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 6

Бренд: Honeywell Страницы: 93

Бренд: Hudora Страницы: 8

Бренд: Dakota Digital Страницы: 14

HelmetTalk HTCS-3C

Бренд: Nady Systems Страницы: 2

Бренд: Chicago Electric Страницы: 7

Бренд: Chicago Electric Страницы: 10

X-FORCE PRO 50 2017

Бренд: Kuberg Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды