Husqvarna F2303U4 Скачать руководство пользователя страница 37

Страница: 37 / 169

PREPARING FOR USE 8

M01459-01

(FE 450 EU)

–

Change the clutch spring.

Clutch spring, hard (78932005000)

8.7

Preparing the vehicle for riding on wet and muddy circuits

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

600868-01

–

Mount the steel sprocket.

–

Clean the motorcycle. (

p. 138)

–

Straighten the bent radiator fins carefully.

M01459-01

(FE 450 EU)

–

Change the clutch spring.

Clutch spring, hard (78932005000)

8.8

Preparing vehicle for high temperatures or slow riding

600868-01

–

Adjust the secondary drive to the road conditions.

Info

The engine oil heats up quickly when the clutch is
operated frequently due to an excessively high sec-
ondary ratio.

–

Clean the chain.

Chain cleaner (

p. 157)

–

Clean the radiator fins.

Содержание F2303U4










































































































































































Результаты поиска

Содержание F2303U4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2303U4, Руководство пользователя

Результаты поиска

Содержание F2303U4

Отзывы:

Бренды по названию

Популярные бренды