Husqvarna F2303U4 Скачать руководство пользователя страница 36

Страница: 36 / 169

8 PREPARING FOR USE

102138-01

–

Mount the air filter sand cover.

Air filter sand cover (79006922000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

600868-01

–

Clean the chain.

–

Mount the steel sprocket.

–

Grease the chain.

Universal oil spray (

p. 158)

–

Clean the radiator fins.

–

Straighten the bent radiator fins carefully.

M01459-01

(FE 450 EU)

–

Change the clutch spring.

Clutch spring, hard (78932005000)

8.6

Preparing the vehicle for riding on wet sand

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

600868-01

–

Clean the chain.

–

Mount the steel sprocket.

–

Grease the chain.

Universal oil spray (

p. 158)

–

Clean the radiator fins.

–

Straighten the bent radiator fins carefully.

Содержание F2303U4










































































































































































Результаты поиска

Содержание F2303U4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2303U4, Руководство пользователя

Результаты поиска

Содержание F2303U4

Отзывы:

Бренды по названию

Популярные бренды