Husqvarna E10 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

background image

104 72 72-26

19

Distance adjustment between shuttle driver shaft gear and lower shaft gear

Check

The axial play of the lower shaft should not be larger than 0.005 mm.

Adjustment

1. Remove free arm cover and base cover. Loosen 2mm Allen screw (a) of feed lifting rod cam. Push feed lifting rock

cam (A) to right.

2. Push lower shaft gear (B) to left tightly against shuttle driver shaft gear complete (C).

3. Push feed lifting rock cam (A) back toward left and secure it tightly.

4. Avoid over-tightening shuttle driver shaft gear and lower shaft gear. If gears are to tight then the torque will be big-

ger causing noise and shaking.

NOTE! This adjusting affect ”Play between shuttle driver shaft gear and lower shaft gear”

«
...
17
18
19
20
21
...
»

Содержание E10

































Отзывы:

Нет отзывов

Похожие инструкции для E10

Бренд: Nancy’s Knit Knacks Страницы: 2

Бренд: Nilfisk-ALTO Страницы: 84

Bernette 340 deco

Бренд: Bernina Страницы: 2

Бренд: Singer Страницы: 74

Бренд: UnionSpecial Страницы: 96

Бренд: White Страницы: 44

Бренд: GBC Страницы: 43

Бренд: Ash Страницы: 30

Бренд: Pfaff Страницы: 30

Autopax PAX200H

Бренд: Quasar Страницы: 76

Бренд: Lavor Страницы: 10

Бренд: Ricoh Страницы: 134

Бренд: JUKI Страницы: 52

Бренд: JUKI Страницы: 4

LK-1900B series

Бренд: JUKI Страницы: 174

Бренд: Miele Страницы: 108

Бренд: promelectroavtomat Страницы: 19

Бренд: promelectroavtomat Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды