Husqvarna E10 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 32

background image

16

104 72 72-26

Play of arm shaft

Check

The axial play of the arm shaft should not be larger than 0.005 mm.

Adjustment

1. Remove the free arm cover, face cover, back cover and front cover.

2. Loosen the 2 screws (a, b) of arm shaft collar (A).

3. Pull hand wheel backward.

4. Push arm shaft collar (A) to left tightly against arm shaft bushing (B) and then fasten and secure screws (a, b).

5. Re-check the distance between arm shaft collar and arm shaft bushing.

NOTE! Be sure arm shaft operates smoothly after adjustment.

Arm shaft collar and arm shaft bushing being too tightly closed might cause insuffi cient operation of arm shaft.

«
...
14
15
16
17
18
...
»

Содержание E10

































Отзывы:

Нет отзывов

Похожие инструкции для E10

Бренд: UNIS Страницы: 19

Бренд: Necta Страницы: 48

SircleBind CB-3000

Бренд: Sircle Страницы: 6

Бренд: HIGHLEAD Страницы: 35

Бренд: Singer Страницы: 20

Бренд: Janome Страницы: 94

WERTARBEIT N 656D Free Arm

Бренд: W6 Страницы: 102

Бренд: A-S-S Страницы: 13

Бренд: Fellowes Страницы: 7

Бренд: KLINDEX Страницы: 32

Бренд: JUKI Страницы: 32

Бренд: Brother Страницы: 204

Бренд: Crane Страницы: 50

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 20

Бренд: promelectroavtomat Страницы: 19

Бренд: promelectroavtomat Страницы: 67

Бренд: Mauser Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды