background image

English-

51

TROUBLE SHOOTING GUIDE

The engine overheats.

Clogged air intake or cooling fins.

Engine overloaded.

Poor ventilation around engine.

Defective engine speed regulator.

Too little or no oil in the engine.

Defective spark plugs.

The machine moves slowly, unevenly,

Parking brake on.

or not at all.

Drive belt for the IZT slack or
has come off.

IZT failure.

Brake/Bypass lever misadjusted.

Mower deck not engaging.

Drive belt for the mower deck has come loose.

Contact for the electromagnetic coupling
has loosened.

The control for engaging the mower deck is
faulty or has come loose from the cable contact.

The fuse has blown.

Uneven mowing results.

Different air pressure in the tires on the left and
right sides.

Bent blades.

Spacers for height adjustment faulty placed.

The blades are blunt.

Driving speed too high.

The grass is too long.

Grass collected under the mower deck.

The machine vibrates.

The blades are loose.

The blades are incorrectly balanced.

The engine is loose.

The machine moves when in neutral postion.•The motion control linkage out of adjustment.

Содержание 968999237





































































Отзывы: