Husqvarna 524 L Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 36

background image

MAINTENANCE

26 – English

Cleaning the air filter

Close the choke valve by moving the choke control up.

Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Clean also the inside of the
filter cover by using air or a brush. Ensure that the filter is
dry before refitting it.

Remove the Felt filter from the filter holder and gently
brush debris from the filter. Check the rubber sealing
surface. Change the filter on the rubber seal if damaged.

An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced
with a new one at regular intervals.

A damaged air filter

must always be replaced.

Damaged, very dirty, or fuel-

soaked air filter must always be replaced.

Bevel gear

The bevel gear is filled with the right quantity of grease at
the factory. However, before using the machine you
should check that the bevel gear is filled three-quarters
full with grease. Use HUSQVARNA special grease.

The grease in the bevel gear does not normally need to
be changed except if repairs are carried out.

H1155734-26,524L,525LST,RJD,.fm Page 26 Friday, March 8, 2013 7:19 AM

«
...
24
25
26
27
28
...
»

Содержание 524 L





































Отзывы:

Нет отзывов

Похожие инструкции для 524 L

SRM-3100 Series

Бренд: Echo Страницы: 40

Бренд: LawnMaster Страницы: 59

TRIMMER ATTACHMENT SRM-261SB

Бренд: Echo Страницы: 32

Бренд: Sovereign Страницы: 16

Бренд: JDW Страницы: 16

Бренд: SNOWJOE Страницы: 20

SunJoe SHARPERBLADE SB602E

Бренд: SNOWJOE Страницы: 11

Sunjoe 24V-SSEG-LTE

Бренд: SNOWJOE Страницы: 16

sunjoe 24V-HT22-LTE-RM

Бренд: SNOWJOE Страницы: 20

Бренд: GÜDE Страницы: 78

Бренд: Vitek Страницы: 32

790 AST Prime & Pull

Бренд: MTD Страницы: 24

Бренд: Kobalt Страницы: 89

Бренд: Wahl Страницы: 8

Бренд: Worx Страницы: 24

Бренд: IDEAL Страницы: 24

Бренд: VALERII S&M GROUP Страницы: 19

Бренд: Yardworks Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды