Husqvarna 524 L Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

background image

ASSEMBLY

English

–

13

Assembling the cutting
equipment

Fitting the trimmer guard and
trimmer head

•

Fit the correct trimmer guard (A) for use with the
trimmer head. Hook the trimmer guard/combination
guard onto the fitting on the shaft and secure with the
bolt (L).

•

Fit the drive disc (B) on the output shaft.

•

Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.

•

Insert the locking pin (C) in the hole to lock the shaft.

•

Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.

•

To dismantle, follow the instructions in the reverse
order.

Assembling and dismantling the
two-piece shaft (525 RJD)

Assembly

•

Loosen the coupling by turning the knob.

•

Align the tab of the attachment (A) with the arrow on
the coupling (B).

•

Push the attachment into the coupling until the
attachment snaps into place.

•

Before using the unit, tighten the knob securely.

!

WARNING!

When fitting the cutting attachment it is
extremely important that the raised
section on the drive disc/support flange
engages correctly in the centre hole of
the cutting attachment. If the cutting
attachment is fitted incorrectly it can
result in serious and/or fatal personal
injury.

!

WARNING! Never use a cutting
attachment without an approved guard.
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.

A

A

B

C

H

H

A

B

H1155734-26,524L,525LST,RJD,.fm Page 13 Friday, March 8, 2013 7:19 AM

«
...
11
12
13
14
15
...
»

Содержание 524 L





































Отзывы:

Нет отзывов

Похожие инструкции для 524 L

Бренд: Weed Eater Страницы: 10

Бренд: Ryobi Страницы: 20

Бренд: Yard Machines Страницы: 50

Бренд: Makita Страницы: 100

Craftsman 536.796526

Бренд: Sears Страницы: 16

Бренд: Philips Страницы: 373

Бренд: PLP Страницы: 22

Vizia RF RZI06-1L

Бренд: Leviton Страницы: 2

Бренд: Draper Страницы: 12

Бренд: Draper Страницы: 12

Бренд: TOOLCRAFT Страницы: 60

Бренд: Talon Страницы: 3

Бренд: Talon Страницы: 6

Бренд: Talon Страницы: 4

Бренд: Talon Страницы: 4

Бренд: Talon Страницы: 4

Бренд: TOOLCRAFT Страницы: 79

Бренд: Scheppach Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды