background image

19

RAISING AND LOWERING

•  Use the on/off switch attached to the side of the 

tractor's dash to raise or lower the snow thrower. The 
winch motor will shut off when the snow thrower is in 

either the up or down position.

CUSTOMER RESPONSIBILITIES

•  Read and follow the maintenance schedule and the maintenance procedures listed in this section. 

Service Dates

 

Check for loose fasteners 

 

  Check scraper and shoes for wear   

 

 

X

 

Cleaning 

    X

  Lubrication Section 

 

 

 

 

 

 

  MAINTENANCE SCHEDULE
 

Fill in dates as you

  complete regular service.

Bef

ore each use

Aft

er each use

Ev

ery season

Bef

ore st

orage

LUBRICATION

 

Oil all pivot points on the snow thrower.

•  Oil the pivot points of the two idler arms on the clutch/

idler assembly.

•  Apply penetrating oil to the control cables of the 

discharge chute.

•  Apply a good grade of spray lubricant to the chute tilt 

control assembly.

CAUTION

:   

Do not operate the snow 

thrower without rear wheel weights 
attached to the tractor to provide extra 

traction and stability.

MAINTENANCE

CHECK SCRAPER AND SHOES FOR WEAR

(Refer to figures 36 and 37 on page 20.)

•  The scraper plate and skid shoes on the bottom of the 

snow thrower are subject to wear. To prevent damage 

to the spiral auger housing, replace plate and shoes 

before wear is excessive.

REMOVING SNOW 

Snow removal conditions vary greatly from light fluffy 
snowfall to wet heavy snow. Operating instructions must 
be flexible to fit the conditions encountered. The operator 
must adapt the lawn tractor and snow thrower to depth of 
snow, wind direction, temperature and surface conditions.
•  Before beginning operation, thoroughly inspect the 

area of operation and remove all door mats, sleds, 
boards, wires and other foreign objects.

•  The spiral auger speed is directly related to engine 

speed. For maximum snow removal and discharge, 
maintain high engine r.p.m. (full throttle). It is advisable 

to operate the lawn tractor at a slow ground speed 

(1st gear) for safe and efficient snow removal.

•  In deep, drifted or banked snow it will be necessary to 

use full throttle and a slow ground speed (1st gear). 

Drive forward into the snow, depress the tractor's 
clutch-brake pedal and allow the spiral auger to clear 
the snow. Repeat this method until a path is cleared. 

On the second pass, overlap the first enough to allow 
the snow thrower to handle the snow without repeated 

stopping and starting of forward motion.

•  In extremely deep snow, raise the snow thrower up 

to the transport position to remove the top layer of 

snow. Drive forward only until the front tires reach the 

uncleared bottom layer of snow. Stop and allow the 
snow to clear out of the spiral auger. Back up and 

then lower the snow thrower to the ground. Drive the 

tractor forward until the snow again becomes too 

deep. Repeating this process into and out of drifts will 
eventually clear even the deepest of snow piles.

•  If the snow thrower becomes clogged with snow or 

jammed with a foreign object, disengage the snow 
thrower immediately and shut off the tractor engine. 
Use a wooden stick to unclog the snow thrower before 
resuming operation.

OPERATING TIPS

•  Discharge snow down wind whenever possible.
•  To help prevent snow from sticking to the snow thrower, 

allow the snow thrower to reach outdoor temperature 
before using it. A light coat of wax may also be applied 

to the inside surface of the snow thrower housing and 
discharge chute.

•  Use tire chains to improve traction.
•  Use rear wheel weights to improve traction.
•  Before the first snowfall, remove all stones, sticks and 

other objects which could become hidden by the snow. 
Permanent obstacles should be marked for visibility.

•  Overlap  each  pass  slightly  to  assure  complete  snow 

removal.

DANGER

:   

Shut off engine and 

disengage snow thrower before unclogging 

discharge chute. Unclog using a wooden 

stick, not your hands.

Содержание 45-04912-669





























Отзывы: