background image

4

CONGRATULATIONS

 on your purchase of a new snow 

thrower.  It has been designed, engineered and man u -

fac tured to give best possible dependability and per for -

mance.
Should you experience any problem you cannot easily 

remedy, please contact your nearest authorized service 

center.  We have competent, well-trained tech ni cians and 

the proper tools to service or repair this unit.
Please read and retain this manual.  The instructions will 

enable you to assemble and maintain your snow thrower 

prop er ly.  Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE:  _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND 

ON A DECAL ATTACHED TO THE REAR OF THE SNOW 

THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND 

DATE OF PURCHASE AND KEEP IN A SAFE PLACE 

FOR FUTURE REFERENCE.     

CUSTOMER RESPONSIBILITIES

•  Read and observe the safety rules.
•  Follow a regular schedule in maintaining, caring for 

and using your snow thrower.

• 

Follow the instructions under “Maintenance” and “Stor-

 age” sec tions of this own er’s manual.

MAINTENANCE ..................................................... 16-17

SERVICE AND AD JUST MENTS ........................... 18-21

STORAGE ................................................................... 22

TROU BLE SHOOT ING ................................................ 23

WARRANTY ........................................................... 24-27

SAFETY RULES ........................................................ 2-3

PRODUCT SPECIFICATIONS ...................................... 4

CUSTOMER RESPONSIBILITIES ................................ 4

ASSEMBLY / PRE-OPERATION ............................... 6-8

OPERATION ............................................................ 9-15

MAINTENANCE SCHEDULE ..................................... 16

TABLE OF CONTENTS

PRODUCT SPECIFICATIONS

Gasoline Capacity

  3.2 Quarts (3,03 Liters)

and Type:

 

Unleaded Regular only

Oil Type

  

SAE 5W-30 or 10W-30

(API SG–SL):

 

(0°F to +40°F / –18°C to +5°C)

  

Synthetic SAE 5W-30 or 10W-30

  

(below 0°F / –18°C)

Oil Capacity:

 

28 Ounces (0,8 Liters)

Spark Plug:

 RC12PYP3

Gap:

 

0.030" (0,762 mm)

Содержание 1650EXLT





























Отзывы: