Husqvarna 1650EXLT страница 8 Скачать руководство пользователя

Страница: 8 / 28

ASSEMBLY / PRE-OPERATION

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR

HEAD (See Fig. 7)
NOTE:

The multi-wrench provided in your parts bag may

be used to install the chute rotator head.
1. Place discharge chute assembly on top of chute base

with discharge opening toward front of snow thrower.

2. Position chute rotator head over chute bracket. If nec es-

sary, rotate chute assembly to align square and pin on un-

der side of chute rotator head with holes in chute brack et.

3. With chute rotator head and chute bracket aligned,

po si tion chute rotator head on pin and threaded stud

of mounting bracket.

4. Install 3/8 washer and locknut on threaded stud and

tighten securely.

CHUTE

ROTATOR

HEAD

3/8 WASHER

3/8 LOCKNUT

THREADED

STUD

PIN

ROTATOR HEAD

MOUNT ING

BRACKET

CHUTE

BRACKET

FIG. 7

ALIGN BEFORE

TIGHTENING LOCKNUT

INSTALL CHUTE DEFLECTOR REMOTE CONTROL

(See Figs. 8 and 9)

1. Install remote cable bracket to discharge chute with

5/16-18 carriage bolt and 5/16-18 locknut as shown.

Tighten securely.

2. Install remote cable eyelet to chute deflector with

1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tight-

en nut securely. Eyelet will be loose on shoulder bolt.

3. Install spring hooks between hex nuts on chute rotater

head and into hole in chute deflector as shown.

HOOK

BE TWEEN

HEX NUTS

ON CHUTE

ROTATER

HEAD

SPRING

CHUTE

DE FLEC TOR

5/16-18

CARRIAGE

BOLT

5/16-18

LOCKNUT

REMOTE

CABLE

BRACKET

1/4-20

LOCK NUT

CABLE

EYELET

1/4-20

SHOULDER

BOLT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

Содержание 1650EXLT





























Результаты поиска

Содержание 1650EXLT

Отзывы:

Похожие инструкции для 1650EXLT

Бренды по названию

Популярные бренды

Husqvarna 1650EXLT, Руководство оператора

Результаты поиска

Содержание 1650EXLT

Отзывы:

Похожие инструкции для 1650EXLT

Бренды по названию

Популярные бренды