Husqvarna 1130ST Скачать руководство пользователя | Manualshive

Страница: 27 / 32

background image

27

KEY PART
NO. NO.

DESCRIPTION

   1   532 14 63-15   Screw, Hex Head 5/16-18 x 3/4
   2   873 80 05-00   Nut, Lock 5/16-18
   3   532 15 54-15   Washer, Flat
   4   817 49 05-08   Screw, Hex Head 5/16-18 x 1/2
   5   532 18 00-17   Bearing, Flange
   6   532 18 01-34   Shaft, Auxiliary
   7   532 17 92-70   Spacer, Plate
   8   532 18 40-79   Plate, Auxiliary
   9   532 18 00-82   Gear, Intermediate (12/58)

10   532 18 00-65   Gear, Pinion
11   532 18 77-14   Rod, Clutch
12   532 18 00-66   Shaft, Long, Hex
13   532 17 88-07   Pin, Pivot
14   532 18 40-80   Lever, Shifter / Wheel
15   532 17 53-44   Trunnion Bearing Assembly
16   532 18 78-57   Bracket, Pivot, Shift
17   532 17 98-31   Ring, Rubber Wheel
18   532 18 40-78   Plate, Rubber Wheel
19   873 93 05-00   Nut, Lock 5/16-18
20   532 17 86-13   Hub, Rubber Wheel
21   874 76 05-14   Screw, Hex Head 5/16-18 x 7/8
22   532 08 51-79   Retainer, Hairpin
23   532 18 01-35   Spring, Bias
24   532 18 00-81   Gear, Axle (58 Teeth)
25   532 17 86-95   Pin, Pivot Lever
26   532 17 53-41   Plate Assembly, Drive
27   532 17 86-21   Shaft, Axle
28   532 17 53-40   Shaft, Short Hex
29   532 18 40-77   Lever, Shifter Plate
30   532 18 40-76   Bracket, Shifter Support
31   872 27 05-05   Bolt, Carriage 5/16-18 x 5/8
32   532 17 88-79   Key, Square 1/4 x 1/4 x 7/8
33   532 17 53-23   Bearing, Flange
34   532 18 40-75   Plate, Drive Mounting
35   532 18 25-04   Spacer, Bearing
36   532 17 53-48   Pulley, Traction Drive
37   532 15 53-77   Nut, Lock 5/16-18
38   819 11 15-07   Washer, Flat
39   810 04 05-00   Washer, Lock 5/16
40   874 95 05-12   Screw, Hex Head 5/16-18 x 3/4
41   812 00 00-12   Ring, Retaining
43   532 17 90-95   Spring, Return
44   532 18 42-06   Pin, Roll

NOTE:

All component dimensions given in U.S. inches

1 inch = 25.4 mm

REPAIR PARTS

DRIVE

SNOW THROWER - - MODEL NO. 1130ST (HU1130STB), PRODUCT NO. 954 22 30-81

«
...
25
26
27
28
29
...
»

Содержание 1130ST

































Отзывы:

Нет отзывов

Похожие инструкции для 1130ST

Бренд: Yard-Man Страницы: 72

Snow Fox 769-00858 (8/03)

Бренд: Yard Machines Страницы: 32

Бренд: HART Страницы: 34

Бренд: Leister Страницы: 4

Бренд: Toro Страницы: 4

Бренд: Black Max Страницы: 36

Бренд: Billy Goat Страницы: 12

Бренд: Kongskilde Страницы: 12

Бренд: Troy-Bilt Страницы: 8

Бренд: Troy-Bilt Страницы: 52

Бренд: Cub Cadet Страницы: 20

Бренд: Cub Cadet Страницы: 22

Gartenmeister GM ALB 40

Бренд: IKRA Mogatec Страницы: 56

Бренд: Ikra Страницы: 32

Бренд: TitanTec Страницы: 16

Бренд: Scotts Страницы: 21

Бренд: Scotts Страницы: 21

Бренд: Scotts Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды