Husqvarna 1130ST Скачать руководство пользователя | Manualshive

Страница: 19 / 32

background image

19

Does not start

1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position.

  equipped) in OFF position.
  2.    Safety ignition key   2.    Insert safety ignition key.
  is not inserted.
  3.    Out of fuel.      3.    Fill fuel tank.
  4.    Throttle in STOP position.   4.    Move throttle to FAST position.
  5.    Choke in OFF position.       5.    Move to FULL position.
  6.    Primer not depressed.      6.    Prime as instructed in the Operation section of this manual.
  7.    Engine is fl ooded.     7.    Wait a few minutes before restarting, DO NOT prime.
  8.    Spark plug wire is       8.    Connect wire to spark plug.
  disconnected.
  9.    Bad spark plug.   9.    Replace spark plug.
  10. Stale fuel.    10. Drain fuel tank and carburetor, refi ll tank with fresh gasoline.
  11. Water in fuel.   11. Drain fuel tank and carburetor, refi ll tank with fresh gas o line.

Loss of power

1. Spark plug wire loose. 1. Reconnect spark plug wire.

  2.    Throwing too much snow.     2.    Reduce speed and width of swath.
  3.    Fuel tank cap is covered   3.    Remove ice and snow on and around fuel tank cap.
  with ice or snow.
  4.    Dirty or clogged muffl er.    4.    Clean or replace muffl er.

Engine idles or

1. Choke is in FULL position. 1. Move choke to OFF position.

runs roughly

2. Blockage in fuel line. 2. Clean fuel line.

  3.    Stale fuel.    3.    Drain tank and refi ll with fresh, clean fuel.
  4.    Water in fuel.   4.    Drain fuel tank and carburetor, refi ll tank with fresh gasoline.
  5.    Carburetor is in need of      5.    Contact a qualifi ed service center.
  adjustment or overhaul.

Excessive

1. Loose parts or damaged 1. Tighten all fasteners. Replace damaged parts.

vibration

augers or impeller. If vibration remains, contact a qualifi ed service center.

Recoil starter

1. Frozen recoil starter. 1. See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

in the Operation section of this manual.

Loss of traction

1. Drive belt is worn. 1. Check / replace drive belt.

drive / slowing

2. Drive belt is off of pulley. 2. Check / reinstall drive belt.

of drive speed

3. Friction drive wheel is worn. 3. Contact a qualifi ed service center.

Loss of snow

1. Auger belt is off of pulley. 1. Check / reinstall auger belt.

discharge or

2. Auger belt is worn. 2. Check / replace auger belt.

slowing of

3. Clogged discharge chute. 3. Clean snow chute.

snow discharge

4. Augers / impeller jammed. 4. Remove debris or foreign object from augers / impeller.

TROUBLESHOOTING

PROBLEM CAUSE CORRECTION

See appropriate section in manual unless directed to a qualifi ed service center.

«
...
17
18
19
20
21
...
»

Содержание 1130ST

































Отзывы:

Нет отзывов

Похожие инструкции для 1130ST

Бренд: EarthWise Страницы: 42

Бренд: Yard Machines Страницы: 17

Бренд: Yardworks Страницы: 20

Бренд: Kärcher Страницы: 25

Groundsmaster 200 Series

Бренд: Toro Страницы: 20

Бренд: MTD Страницы: 34

Бренд: Silvercrest Страницы: 20

Бренд: Silvercrest Страницы: 27

Бренд: Silvercrest Страницы: 34

Бренд: Silvercrest Страницы: 34

Hurricane Plus HT0805H

Бренд: Parker Страницы: 8

Бренд: Flymo Страницы: 52

Бренд: Garland Страницы: 112

Бренд: IHP Страницы: 4

Бренд: Task Force Страницы: 15

Бренд: Worx Страницы: 12

Бренд: Worx Страницы: 20

Бренд: Worx Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды